I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hi,
We are having trouble configuring our PDM peripheral to operate at 48 kHz. THe nRF5340-specific documentation on the PDM module has equations suggesting that 48 kHZ...
Hi Folks, I’m working with an I2C LCD rated for up to 50KHz and it is showing a fair number of glitches. Can anyone tell me how to lower the I2C speed from the default values...
I'm writing a custom bootloader for an nRF52840 using the nRF5 SDK v15.0.0. This bootloader uses the SoftDevice to receive BLE packets containing binary data for the DFU....
Hello,
I am evaluating the nRF9161 and nRF9151 and have a few questions.
1. In regard to modem FOTA delta firmware updates, where is the delta file stored in both Serial...
My SPIM seems to stopped working when migrating from NCS 2.5.0 to 2.7.0, so I decided to downgrade to 2.6.0, and it seems the issue is still there. When migrating to 2.6.0...
I have asked this before, but I will ask again.
I have a few questions about the sample source of nRF5340 Audio.
1. Where does the connection process between the gateway...
Hello,
the BSI (German Federal Office for Information Security) released a document February this year which contains a list for recommended cipher suites and TLS versions...
hi ,I am using nrf52840dk- nrf52840 board to interface the IMU Sensor using I2C using nrf connect sdk for vs code. But I am facing error:
i'm using the code in ncs/samples...
Hello im using basic usb over console exaple on my custom board . i believe this task wont require any pins to be configured as my custom board is routed properly to all 4...
Hello,
with the help of this documentation ( https://docs.nrfcloud.com/Devices/MessagesAndAlerts/SetupMessageBridge.html ) i have been able to create a bridge to transfert...
I am trying to test a nRF5340 with a 1.3 inch waveshare 240x240 display using a st7789 driver. How would I connect the display to the board:
VCC
3.3v
...
sdk-nrf: v2.7.0
When PAWR is enabled I no longer get connection timeouts as a callback to bt_conn_cb.connected with the conn_err parameter set when attempting to open...
On the nRF51, LO leakage was measured when in receive mode. For 2402~2480mhz, LO leakage was measured at approximately 2745~2836mhz. The nRF52 does not measure LO leakage...
Hi,
I am using nrf52832 board and I want to configure the SPI0 and SPI1 for the sensors LIS2DW and BMP388 respectively.
I am new to nRF Connect SDK for VS code, I am exploring...
I have installed version 5.0.2 for NRF connect Desktop and on that I have been trying different versions of tool chain manager ranging 1.3.0 to 1.5.1 none of them is loading...
