Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi! I'm new to using the Nordic products and I wanted to be able to power my Thingy 91 device without the use if the USB and with a separate external power supply. On the...
Hi there,
Currently we are developing our own system to drive WS2812B LED's using the NRFX pwm library. And the coloring and signaling works fine when it is in a bare metal...
Hi,
I am using nrf52840 and SDK17.1.0.
I need to calculate CRC16 for communication with an another module. I found that we have an API for that. I would like to know what...
We are planning to develop an Matter door lock which includes NFC/RFID, Audio, keypad and BLE functionalities used separately. I am considering using either the nRF52840 or...
I tried setting the VDD voltage in the 9161 DK to 3,3 V, but it remains at ~1,76 V.
I'm able to enable/disable the GPIO extender just fine, so at least reading & writing...
I have had great success developing a project based on the peripheral_uart sample. Now I am trying to add DFU over UART to that project. Specifically, I would like to add...
Hi,
I have the following minimal example:
main.c
proj.conf:
Now, when setting CONFIG_SERIAL=n my nRF52840DK drains about 3-4 µA, when setting CONFIG_SERIAL=y it...
I am attempting to use the automatic WiFi connection feature described here:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/libraries/networking/wifi_mgmt_ext...
Hello,
I'm trying to merge together a couple of sample projects to make a prototype (in particular, the LTE-BLE gateway, and AWS-IoT samples) - to run on the nRF 9160DK...
I used nRF52840 board with SDK 17_1_0 ,
VL53L5CX driver I want to transfer large amount of data on I2C but when i try to write it then first time nRF52840 restart and after...
Hi,
What is the correct way to build an application (say asset_tracker_v2) included in a newer SDK (2.6.1 for example), using a nRF9160 DK without on-board SPI flash device...
Hi,
I have a bunch of openthread routers and TTM shows one as in some error state.
RLOC is 0x9400, but no ext address is shown.
Also a child connected to this router...
Hi everyone,
I am planning to use the cadence/publish interval property within a mesh network. I can not find any examples on how to use it. I know I can set it in the nrf...
I'm developing a BTLE sniffer app to run on a headless raspberry pi 4 with html/php/js access. The application runs well on the development platform - Ubuntu 22.04.
On the...
We have some custom hardware that utilises an NRF52832. Up until recently, all our firmware was built on NCS V2.2.0, which I believe used Zephyr V3.2.99. We have implemented...
