Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Dear Nordic Community, I want to build samples/basic/blinkly on nordic nrf52840_dongle inside my Zephyr workspace. I use Zephyr 4.2.0, but on Zephyr 4.3.0 I have similar problems...
Hello, I am looking at pages 871 and 872 of the datasheet for the QFN48 package, but I’m not sure I understand correctly. Could you please tell me which GPIO P0 pins can be...
I’m using an nRF54L15 evaluation board obtained from a distributor and currently testing transmission and reception of large data chunks. Everything was working fine until...
I have an external device. After connecting it to the central device, I found that the Bluetooth service of my external device couldn't be enabled properly. When I checked...
Hi, I have the radio_test example running correctly on a nrf52840 dev board. I am able to use the Nordic Serial Terminal (v1.6.0) to send commands and read responses.
...
I am developing a custom board using nrf54l10 chip. So far, I have been able to use a code to comunicate through spi and uart for me to use printk function.
Now I was trying...
The docs( docs.nordicsemi.com/.../dect.html say that th nRF9151 modem can't do GPS/LTE and DECT NR+ at the same. Could the modem switch between the two operation modes while...
Hello team,
I am using SPI00 of NRF54L15 to communicate with w25q32fv (spi Flash). Below is the configuration I set in .overlay file
And below is the code I am using...
Hi,
I have a question about the the fields " tod_toa_reflector" and "toa_tod_initiator" in struct bt_hci_le_cs_step_data_mode_1.
I understand that these values represent...
The e-mail contains news of a new use of the nRF9151 module but uses the word "proves" and as an English language Cambridge qualified teacher I must mention that the word...
Issue description
I am using SAADC in single-ended mode with 3 channels (0/1/2). Measurements are performed by enabling SAADC, running offset calibration, configuring the...
Hello,
I have an application running on legacy NRF SDK and using the nRF5 bootloader, which has below flash sectors, 0x00000 - 0x026000 - Soft-device section 0x26000 - 0x0D9000...
Our custom product, based on the nRF52832, is undergoing certification. The testing laboratory requires that only one BLE advertising channel be active at a time—first channel...
Hi there,
We have a mass produced product with a modified secure bootloader (from SDK17). This BL has BLE and USB and we bolted on an SPI flash transport for OTA updates...
