To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
I have a custom board with nRF52832 with external spi flash and I'm using SDK 17.1 and softdevice s132 4.0.5. I will use OTA-DFU to receive the new firmware image from...
Like several other folks, I have been attempting to replicate the results in the Matter webinar here , but updating to the v2.1.0 SDK and using the Nordic dev kits I have...
Hi ,
I am working on NRF52840 microcontroller, I want to implement blinky LED for P1.09 GPIO pin, can you please tell me, how to implement that.
Thanks
Hello!
The company that I work for has built a gateway that uses the nrf52832 as a ble central device (nrf5 SDK and the s132 softdevice). Customers frequently ask us to...
Hello Nordic support:
How to reduce nRF9160's LTE-M TX power in coduction test. Is there any AT command to reduce TX power? Or could you give us some guide about how to...
I am diagnosing pin malfunction in a custom board where I have working code from another version of the board which no longer works.
I am developing against NCS w/ VSCode...
Hi,
When asking to change the toolchain version in the VSC extension I get an error message:
Command 'nRF Connect Select nRF Connect SDK Toolchain' resulted in an error...
I am using the current nrf-sdk v2.1.0, which includes a Zephyr version (3.1.99 etc.) which has at the used stage an error with twister: instead of using get_testsuite the...
Hello,
I tried to run the sample Bluetooth: Periodic Advertising but I found some issue.
I'm using SDK v1.9.1.
The first issue was related to advertising creation with...
Before I go deep into the rabbit hole, I am wondering if anyone has had success with the following:
I am in a Windows 11 environment
I want to setup Docker with nRF...
Hi Community & Nordic Semi
I have an ultra low power design using the NRF9160.
I would like to avoid adding an additional LDO to reduce costs and Iq.
VIO from the datasheet...
Hello Community, i'm currently working on a custom board based on BC40C which is a BT/BLe module based on nrf5340 i'm trying to debug my board with jLink ultra + under, i...
There is an examples that show how to change from a 2Mb/s to a Coded 125Kb/s ?
May I change the bit rate of the comuniucation dinamicaly ? For examples I see that with a...
Hi there,
The mentioned known issue needs a workaround requiring a soft reset. This is quite a bruteforce method and I can't believe this hasn't been fixed already. Quite...
