We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Dear all,
I have some problem with SPIs co-work.
I enabled two SPI instances in this project.
SPI Instance 1 function(non blocking mode - DMA enabled, 4Mbps): reading...
Hi there, Thanks in advance for your time and attention. We started to see some cases where our devices boots and gets a NO_PAGES error after having been turned off(or at...
I try to simulate system hang by adding while(1) after calling watch dog feeding function. But watchdog event handler _wdtEventHandler() isn't called.
int main(void) { ...
Hi,
I am currently trying to read the GPIO latch register in my Zephyr NRF SDK 1.9.1 C++ project with the following line:
This is resulting in the following compile...
I have downloaded the nRF connect for PC and successfully managed wo work with the dongle using the BLE General tool but when I tried to use the power profiler tool probably...
Hello Nordic Team,
I have a nRF52833 DK and I am running Light switch Server and client applicaiton in it.
I am in the moment customizing the application for our custom...
Is there a way to disconnect from devices that have exceeded the maximum number of connections allowed?
I am developing with nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral...
When I want to implement my edge impulse model to my nrf5sdk code using vs code I found this errors,
Terminal will be reused by tasks, press any key to close it.
> Executing...
I've just updated my nRC Connect SDK from V1.9.1 to V2.0.0. I did this via the nRF Connect for Desktop Toolchain manager. I'm using the nRF Connect extension in Visual Studio...
Hello everybody,
i currently develop two devices, one master and one slave (sensor). Both devices have the dfu service completly working.
My problem is that the master...
Hi
I am trying to FOTA download with AWS S3 bucket.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/nrf/libraries/networking/fota_download.html I am using HTTPS...
I installed the nRF Connect extension pack which also contains the nRF Terminal extension but I cannot make it work in VS Code
In the command pallette I select nRF Terminal...
Is there a way to manually initialize the nRF5 802154 radio?. I am using an external NOR flash LittleFS partition for data and the nRF5 802154 radio driver keeps complaining...
I'm trying to make some driver code to talk to a flash chip via SPI. I'm using the nrf5340 and SDK 2.0.0. I'm also doing this for the secure board environment the DK app,...
Hello,
We are developing an application to work as a multilink central with 3 different kind of BLE devices that include 1 custom device which advertise customised NUS...
