Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
I'm getting the following linker errors after switching to the latest version of the SDK (17.1.0). I believe I've included the files that define the offending macros (for...
I've made a basic QSPI setup for an MT25QU512. By default the QSPI driver is using 24-bit addressing. To access all of the memory, I'd like to set up the QSPI driver to use...
Hi,
Currently, we have a device that uses the nrf52832 custom board as a Peripheral notify to send the data collected to Pixal 5 (central),
We have a cellphone app to...
Hello Nordic / Zephyr experts,
I am looking for AT command parser for the UART of nRF52840. Want to send and receive AT commands to a LTE modem using MQTT messages. Need...
Hi,
I am aware that nrfutil does not work for OTA updating the nRF53 and was wondering if there was a similar tool that will allow me to achieve this? I need to update ...
Dear BT Mesh experts,
What's the advantage/disadvantage of using the nRF5 SDK for Mesh compared to the nRF Connect SDK ? Consider a rather simple BT Mesh device that provides...
Hi support Team,
Is there a way to make the nrf52840 to connect with only given MAC address (i.e., a MOBILE) ? The MAC address (i.e., a MOBILE) will be changed dynamically...
Hi Support Team,
What's the UBM pad diameter of nRF5340-CLAA?
BTW, any correlation between it and label 'b' in Mechanical specifications in PS?
Best regards
Sal...
When I try to open the .overlay file in SEGGER it shows me an error : "Can't Read file" with the message "Can't open xxxxxx/xxxxx/xxxx.overlay for reading.
Has anyone else...
Hi,
I am running Homekit over Thread sample(NCS/Homekit tag v1.7.0 using MTD-SED conf) on my custom board and I found that the QSPI Flash (MX25R64, as same as the one use...
I want to test OTA in button mode. I have configured the button in DFU project. Now I upload the files in my device in the following pattern:-
1)Bootloader hex file
2...
Hello,
I have an nrf5340-dk board and I am trying to play around with the different baud rates through changing the overlay file (as shown):
I am using teraterm...
Hi guys,
After weeks and weeks of trying with 3 different boards (Thingy91, nrf9160DK and Custom board), combination of different LTE Antennas, Bell, Hologram and iBasis...
I am using nrf52840's dongle development software, and I found that when the slave device sends LL_SLAVE_FEATURE_REQ , the host will return LL_UNKNOWN_RSP. I want to know...
Using the NRF connect app we can simulate the problem we have in our app Cowboy. Some customers cannot pair with the bike that uses the nRF52840. We have secure and non secure...
