I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hi all,
when I follow the blog as below, find the actual output is not same as expected.
Adding a Peripheral to an NCS Zephyr project - Peripherals And RF Test - nRF Connect...
Hi Everyone,
I recently purchased the NRF52840 DK with a PCA10056 designation. I connected the DK to my Windows 7 laptop via the USB. This resulted in the JLINK(D:) drive...
I have a custom board with a nRF52805 module but I don't understand how the SDK works.
I followed some guide to simulate nRF52805 software, I had to patch some files in...
Hello,
I add sd_ble_gap_phy_update() in the ble_evt_handler() as below:
case BLE_GAP_EVT_CONNECTED: { ...... ble_gap_phys_t const phys = { .rx_phys = BLE_GAP_PHY_2MBPS...
The CONFIG_CLOCK_CONTROL_NRF_K32SRC_EXT_FULL_SWING=y Kconfig option causes kernel booting to hang at line 505 of clock_control_nrf.c.
This is on the v1.7-branch of NCS ...
I have created a custom board containing the nRF52832. I have two copies. The first board works, meaning that I have flashed the code to it using the DK52, and I can power...
Hello,
I have been evaluating the nrf9160 DK board. And my application is using mbedtls (vanilla) and TFM (Used https_client as a starter project). The problem is that with...
Hi,
I'm new to nRF/Zephyr development and trying to integrate the OV7670 camera with the nRF52840 board. Since there was no driver for this particular camera I ported the...
I'm having a problem with what should be a very simple exercise. I'm trying to compile the Zephyr sample subsys/cpp/cpp_synchronization after adding #include <string> to the...
Hello,
I am trying to read data from LS2DE12 accelerometer MEMS chip via I2C bus and I am seeing only zeros for all 3 axes.
I can write to the various registers successfully...
Hello, I ran the nrfconnect (ver 3.7.1) in Power Profiler (ver 3.1.3) in BLE advertising.
When I run the source mode on 3000V I get normal peaks (20mA), however when I run...
Hi,
I'm interested to use AGPS in my project. Looking into AGPS example (link below) , I want to prevent using low power mode since as far as I know using this command you...
Power Profiler software returns an error after I updated it to v3.2.0 with nRfConnect v3.8.0.
Error message: Error while probing devices: EnumerateWorker json error
Resulting...
Hi,
I am working with nRF52833 DK with nRF Connect SDK. All was going great until I had to add a GNU GSL library. I need it because I need matrix multiplications with complex...
