Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
Hello
i have a design limitation for height in my product and i need to find another inductor with a max height of ~0.5mm can you please share more information regarding...
Hello Nordic team,
I've recently upgraded my application from nRF Connect SDK v2.7.0 to v2.8.0 , and the previous BLE Disconnect issue has been resolved — thanks again for...
I am in the process of migrating an existing project from 2020 to the newest version of Zephy/Nordic. I am having issues with the I2C bus. I created a test project using the...
Hello, I'm trying to connect my nrf7002dk board to wifi with Zephyr. I'm using this sample : https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/wifi/sta/README...
Hi,
We are evaluating NRF5340+NRF7002 setup for our customer. We are currently using https client example(sdk v3.0.2). I see that with this example the boot time of the...
I am using the nRF54L15 and NCS SDK v3.0.2 in my project. I need to wake up the board via interrupts from a pressure sensor and a gyro sensor.
The GPIO requirements are...
Hello
I compiled the zephyr example ../zephyr/samples/drivers/i2s/output
The SCK and MCK Signal do have both the same frequency. The bit positioin on MSB in not in the...
Hi there,
This is a follow up post from my earlier one here about using nRF5340 dk as an I2S master for the purpose of recording sound using a MEMS sensor ICS43434. Here...
I’m implementing static passkey security in a BLE peripheral using nRF52810 with SDK 17.1.0. I have added a feature where the device disconnects automatically if the user...
Hi,
I'm working on software for a design incorporating an Ezurio module that uses an NRF54L15 chip.
I'm currently using the peripheral_uart example as a base for early...
According to the nRF52832 Product Specification, “A step increase in supply voltage of 300 mV or more, with rise time of 300 ms or less, within the valid supply range, may...
Hello,
I am trying to get confirmation regarding if I should expect to receive DeviceShadow events through the nRF Message Routing Service.
https://docs.nordicsemi.com...
Hi.
I made the smallest system module using nRF52840. The schematic diagram is as follows.
My reference design for power supply is as follows,
For Firmware....
I am using nrf5340 audio DK. After plugging it into the computer, 3 VCOMs and RTT will appear. What are these three ports? docs.nordicsemi.com/.../logging_nrf5340.html Here...
I am using nrf5340 audio dk, v3.0.2 SDK. I added CONFIG_BT_TINYCRYPT_ECC=n in prj.conf and got this error: C:/ncs/bumble/hci_uart_0806/prj.conf:23: warning: attempt to assign...
