Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hello,
I am using your NRF9160 chip and need Nordic team help. I have refer to your FOTA sample, I am looking for a safer solution for updating code. On my board, I use...
Three software seems to perform OTA DFU: nrfutil command line, nRF connect from desktop, nRF connect from mobile
Do I need all three of them? Are they part of Nordik SDK...
Hi,
I am using an Adafruit nRF52840 Express with a sensor board attached to it. I'm noticing that my sensor IC is reading about 3-6dB higher noise in the 10-50Hz range ...
Hello,
I want to program and debug a custom PCB using the nRF52832 SoC and nRF52 DK. I plan to use this setup:
From what I understand, the GND detect will cause the...
Hi Nordic team,
We are busy testing the throughput of the nRF9160. We are having issues installing the NCS at this stage, and was thus provided with a HEX file of the Serial...
Hi Nordic engineers,
I am using west to build the nRF NCS, my own project which is adopted from samples. Using Powershell (win10) to run west commands as below.
I need...
I tried the "ble_app_hrs_pca10040_s132" example from SDK17.0.2 on an ISP1507-AX and wanted to access the Heart Rate Service to read out Heart Rate and Body Sensor Location...
Hey guys ,
I am trying to merge ble_app_uart code with RTC peripheral code . RTC code works fine when I try it on SDK but after merging with ble_app_uart code it doesn...
Hi,
I have a question about the connection handling when we have two connections to a single smartphone.
The smartphone runs two Applications:
App 1: Acts as central...
Hi,I recently started using a PPK2 board and at first had no trouble setting it up with the Power Profiler Software from the nRF Connect for Windows.
What I realised is...
Hi,
nRF9160 in nRF9160DK with NCS v1.6.0 and master, power consumption measured by PPK2.
With CONFIG_SLM_EXTERNAL_XTAL=n nRF9160 average power consumption is ~7uA after...
My use case is that the nrf9160 is running as a serial lte modem and I have a host controller that is controlling the ENABLE pin. VDD will always be powered so can I leave...
Hi All,
I am using a 3rd Party (Japan) nRF51822 module in a device and it is running a modified Direct test mode firmware without Soft device. Upon testing, it is found...
