Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
Hello!
I'm trying to perform DFU over BLE using a nRF52840-Dongle (PCA10059) devkit. I'm getting the following error:
I've tried to add '-cd 5' and '-f' options...
The OPS states the maximum transmitter RF power accuracy to be +/- 4 dB. Does this imply that if the power is set to +4dBm it could vary from 0 dBm to as much as +8 dBm? What...
The documentation is a little unclear. I am using Arduino Nano 33 BLE. Using the analogread() functions of Arduino I get a much worse performance than the nRF is supposed...
My application is composed by three different source code repositories, organized as follows:
+--- app
L---- lib1
| L-- src
| L-- include
L---- lib2
| L-- src...
This is a bug report for the NRF9160 AWS FOTA implementation tested with nrf-sdk at 25c4404f1
My application is based on the asset_tracker_v2 example.
When I initiate...
I am attempting to develop software for a wearable device that hikers/athletes will use in the case of emergency. It will send out an emergency message when a button is pressed...
Hello,
I am trying to use part of the code from this example https://github.com/zephyrproject-rtos/zephyr/blob/master/samples/subsys/nvs
to write to and read from flash...
Hi
I'm trying to use the battery sample to create some code that reads the battery level at boot. However I'm experiencing what I believe to be a race condition
If I run...
Hi Dev team,
I have been working on a Thingy91and I was trying to read out the battery voltage of the device.
I was able to do that through the modem using the MODEM_INFO...
I am trying to send just random dummy data to my android app. First of all, I am not expecting or need the confirmation, so I should be using the notification and not indication...
I have referenced the following document.
https://www.nordicsemi.com/-/media/DocLib/Other/User_Guides/nRFSnifferUGv22.pdf?la=en
I checked the contents up to 2.3.
However...
I have configured nrf9160 dts common file with one SPI3, I2C0, UART1 and UART2. Also i changed chosen section in the dts file to use UART1. When i build and run on nrf9160DK...
Hi, everyone on the community
softdevice: sdk17
I added the BLE_APP_UART peripheral function to the scanning project, but the device is wrong when the phone is connected...
we develop the TWI I2C interface, already setting the Enable TWIM driver in the Project Setting. but.
the code :
const nrf_drv_twi_t m_twi_instance = NRF_DRV_TWI_INSTANCE...
