Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
I have a service with 2 characteristics, TX and RX. On TX the notify is enabled, because TX should send a notification when something changes. I manage to change what is needed...
Hello everyone.
We have a design based on NRF52840, which uses the built in USB peripheral and was fully tested and prototyped using NRF52840-QIAAD0-2031MR. We have now...
Hi There,
I have downloaded the nRFgo studio and nRFgo SDK and other files found here: https://www.nordicsemi.com/Products/Low-power-short-range-wireless/nRF24-series
...
For the MPSL/timeslot example in NCS 1.5.0, I am trying set up a TIMER0 compare interrupt to take clean-up actions before the timeslot ends, as suggested in here . However...
Describe the bug Attempted to use the samples/bluetooth/hci_usb/ project with CONFIG_BT_EXT_ADV=y CONFIG_BT_EXT_ADV_LEGACY_SUPPORT=y CONFIG_BT_EXT_ADV_MAX_ADV_SET=4 CONFIG_BT_PER_ADV...
Hi, I have the Power Profiler Kit PCA63511 used on top of the dev kit PCA10040. I am trying to measure the power consumption of my custom hardware implementing nrf52832 using...
I'm already using nrf51 in a project and now I need to make a DFU with BLE using a gateway. For the gateway project, I was thinking of using a nrf5x to implement a DFU master...
Hi , a day ago i recived my first dev board from nordic semiconductors, the nRF5340 . Until now I only coded for AtMega328 , esp32, esp8266 and other microcontrollers like...
I am trying to build the aws_fota example project for the nRF9160 using the nRF Connect SDK and the Segger IDE. We currently have v1.5.0 downloaded. The project is not compiling...
Hello everybody,
i use two nrd52 dk boards with nrf mesh light server flashed on them (mesh sdk 4.2.0)
They are configured over nrf mesh app to be in the same network...
Hi, I have nRF52840 DK. How can set the max range? or how can increase/decrease the tx range? Also is there any range extender to improve range? Thanks!
Hi,
I am currently doing a uart dfu over 2 nrf 52840 dks on a Windows PC. I have been using the example found in ...\examples\dfu\secure_bootloader\pca10056_uart_debug supplied...
Hello,
I am porting the secure serial bootloader from the nRF52833 DK (PCA10100), in which it works fine, to my custom board. I press the button and turn my board on to...
Hello, all
Following this ticket ( Configuring ADC sampling rate and simultaneous reading from multiple channels. ), I found a great example code that sends readings from...
