Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hi,
For both (nRF52840 / nRF52832 ), with SDK version nRF5_SDK_15.3.0_59ac345
I am using Secure_Bootloader in the eample folder:
nRF5_SDK_15.3.0_59ac345/examples/ble_peripheral...
I found an issue when using CONFIG_AZURE_IOT_HUB_DEVICE_ID_APP to set the Azure Device ID.
Around line 88 of azure_iot_hub.c the "user_name" structure is set using the...
Hi,
Is it true to say you have two modem firmware streams: 1.1.X and 1.2.X? Are these two kept in sync in terms of GNSS improvements? I notice the 1.2.2 release notes mention...
Hello,
I want to measure current consumption of nRF9160 of the Thingy 91 with the Asset Tracker application in PSM mode without GPS. For that, I added to the function modem_configure...
Hi,
Browsing the API I only saw Enhanced shockburst support. I need air compatibility to an old 250kBit plain Shockburst communication. No auto ACK and no auto retransmit...
I have run up the CLI example to test as we will require some command line interaction and why reinvent the wheel?
I run up the example with USB enabled and UART disabled...
Hello Nordic,
I try to establish communication between an ATmega328 based board an an Arduino Nano, so far without success. The goal is to improve a RF433 "Wire". 3 weeks...
Dear All, I am using the ADC to measure 3 voltages applied on different ADC inputs and 3 different channels. My ADC configuration looks like this: And this is how I am performing...
Hi,
I recently acquired the nRFgo starter kit and nRF2724 rev 2.1 and the nRFgo development kit. I have downloaded all of the supporting software that were found here...
I have the latest nRF Connect for Desktop.
After I install "nRF Connect SDK v1.4.99-dev1" in Toolchain Manager I don't have an "Open IDE" button.
I've tried uninstalling...
I am adding JLINK_MOITOR.c and JLINK_MONITOR_ISR_SES.s and add write
#if CONFIG_JLINK_MONITOR_ENABLED NVIC_SetPriority(DebugMonitor_IRQn, _PRIO_SD_LOW); #endif
at starting...
Hello everyone,
I'm trying to develop an application with BLE, using an example as a base.
The advertising is good, well configurated, I can edit manufacturer specific...
I am currently using Mesh SDK 4.2.0 and I could successfully write and read reliably from the flash using a second flash manager instance used in parallel with the flash manager...
HI，All:
the softdevice.hex has inlcuded the bootable/strat code,as the figure below ,how to separate the bootable code from the hexcode?
in the SEGGER IDE:
in...
