Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Dears,
Diagram as attached, we want to make a audio recorder design.
Customer wants to recorder the audio, and at the same time do audio player works.
Is it possible...
I'm evaluating nRF52840 DK.
Currently running peripheral_lbs example.
I'm trying to set security level to BT_SECURITY_L4
I'm connecting to nRF52840DK with via smartphone...
Hi,
I'm using the nRF5340 DK and SES 5.34a, nRF Connect SDK v1.4.2. For python, I use pyenv virtual environment for which python is set to 3.9.1.
I am able to build and...
Hello I have a question. After when I have used saadc, the consumption increases by 0.9mA. And stays it so. Do you have any idea, how to find out what it does?
saadc init...
Hello,
I'm using a nRF52832 chip and attempting to broadcast a public MAC address through the application. I'm observing that the device broadcasts MAC Address FF:FF:FF...
Hi.
I am building my application on top of ble_app_uart__saadc_timer_driven__scan_mode example.
I want to interface an i2c device with it. The i2c device works perfectly...
Aim:- To read temperature and humidity over a mesh network and display it in an android application
Devices to be connected in Mesh :-
nRfF52840 Development Kit x2 ...
Hello,
I am currently working with nrf 52840, using segger embedded studio (V5.34) and SDK 17.0.2.
For some reason, when I open any example under ble_peripheral, such...
Hi,
I installed nRF Connect SDK v1.4.2 by the tool chain manager and was following the Getting Start guide and entered here.
https://developer.nordicsemi.com/nRF_Connect_SDK...
Hi,
I have two variants of the nrf9160 SIP one being the nRF9160 SICA B 0 A and the other being the nRF9160 SICA B 1 A.
When I use the AT%HWVERSION AT command on the B0...
Hi,
I want to write my own Multilink/UART example from scratch, because I'm too confused from all these examples.
What I need to get that code done? Or has anyone build...
I am trying to download the softdevice to the nRF52840 development kit using the nRFgo but:
1. On nFRgo I didn’t found the “Program softDevice tab”
2. Although the kit...
Hi
Migrating from NCS1.3.1 to NCS1.4.1, the Blinky sample stops working on my custom nrf5340 board. No compile error, but not running. I also have a nRF5340PDK. Works fine...
I want to use long range ble for advertising with nrf52833. I have a PCA10100 SDK board, and I'm running a program with type of BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_SCANNABLE_UNDIRECTED...
