Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We are about to use the nRF52832 and are looking at which SofDevice to select for a Central-only implementation. The S122 summary says it targets the nRF52820 and nRF52833...
i m using NRF52840 with sdk 15.2. In that i m testing direct test mode by UART.Now i can do transmit mode.i can check through nrfconnect dtm mode. i cannot check receiver...
Hi,
I tried the following AT settings on the nRF9160 DK board:
AT+CPSMS=1,,,"00111000","00011110"
AT+CFUN=1
After this the modem enters PSM mode and the current is...
Hi,
One of our modules using PCA10090 0.8.2 programming and production nRF9160/nRF52840 modules.
Our customer reported that they can't use PCA10090 0.9.0 re-programming...
Hi! I ran into a little misunderstanding in setting up clock frequency for PDM. I need to work with lower clock frequency than default - 0.64 MHz. I see, that PDM_CLK = 32...
Hi,
Some questions on the scan consumption of nRF52840 and using the attached Online Power Profiler for BLE as reference
If I am using my nRF52840 to scan 24hours at...
I wish to merge the cloud_client example with GPS example. How should I go about it? Along with main.c files of both, which other files will I need to merge?
I am currently making a program that will interpret serial commands from UARTE1 and then send + read something from the other (UARTE0). Previously, when I have been using...
Hello,
I want to be able to send 1 MB of data from a server node to a client node
I have made a simple model with an array that holds 300 bytes.
and upon a timer the...
Hi,
I want to connect Multi peripherals to one central and want to send the device name(peripheral which is connected) through the uart.
How do i get the device name which...
I have seen some variations of this issue but hoping someone can lead me in the right direction.
Similar to others, I am using NRF_LOG_INFO for debug messages. It works...
Hello, I am working on a project which uses nrf52832 module ( https://www.seeedstudio.com/MDBT42Q-nRF52832-based-BLE-module.html ). I just want someone to review its circuit...
Hi!
I'm slightly confused with the documentation regarding softdevices S112 and S113. Among other differences, its noted that SD S113 does not support nrf52820 chipset while...
Hi, I have a custom board based on nRF9160 for which I created custom .dts following porting guide. It seems TX isn't sending anything (stay close to 0V) - config I have is...
