We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hi everyone,
Looking the examples of SDK16, I noticed that every example has a hex folder with some .hex files inside . This applies for both peripheral and ble examples...
Hello,
I want flash NRF52840 using AM57xx sitara processor(running on linux) over SWD interface. Can you please provide steps for the same. Is there any other methods available...
Hello,
We are using nRF52840 with SDK 15.2.0, a bootloader and the SoftDevice. We are able to perform a DFU by downloading the .bin and .dat files of the new firmware in...
Hi,
Following the example https://infocenter.nordicsemi.com/topic/sdk_tz_v4.1.0/thread_example_dfu.html how can you connect a jlink debugger and step through the application...
I read here...
NRF52840_PS_v1.1.pdf Peripherals > UART (6.33.7)
“An ERROR event, in the form of a framing error, will be generated if a valid stop bit is not detected...
Hi,
is there an updated example for SDK 15 or 17 for the multiprotocol example which uses BLE and ESB via the timeslot concurrently and at the same time allows the normal...
Hi ,
i am new to using SPI and i am currently undergoing my final year porject that consits of data analyisis for IMUs and i am uding the nrf52DK (which i never used before...
Hi Everyone I have been trying to send a text file(reading from SD card) , The size of the file is 2MB. I am using softdevice s132 for nrf52832 to transfer the text file via...
To Nordic support team attention,
Hi guys, in sdk16 there is ble_app_gls example. I slightly modified it so to have BLE_GAP_IO_CAPS_KEYBOARD_ONLY as GAP IO Capabilities...
Hello, we have an application with BLE. We've prepared secure bootloader with Serial Transport for performing DFU. Now we need to add necessary changes in application to support...
Hi everyone,
I want instead of MAC address to advertise my device using its 64bit unique ID. What I am considering, is to use the p_data array for that purpose and more...
Hi, I see an interesting situation.
I got flash corruption with values 0xff after random power cycling and it's happened only if I have flashed the bootloader
soft device:s132
sdk:15.3.0
I implemented the following, but the event does not occur even if the voltage is V2.8 or less.
Do you know the reason?
===
NRF_SDH_SOC_OBSERVER...
The nRF5 SDK's throughput sample (ble_app_throughput) provided very convenient shell commands to configure key parameters affecting throughput in a connection, such as ATT...
