To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi
Can anyone verify that it is possible to use the nRF5340 PDK to program custom nRF53 board?
The documentation says: The nRF5340 PDK supports programming and debugging...
Hello,
we are using NRF9160 +Nrf52832 in a project. NRf52832 has to be used as HCI interface..after searching for this, i came to know that zephyr based HCI uart sample...
Hi,
I am working on Eddystone project, after I successfully tested the Buttonless DFU example, I added DFU service to Eddystone example ( nRF5_SDK_17.0.0_9d13099\examples...
I am using this MBN52832DK and find out this nRF5_SDK_17.0.0_9d13099.
Trying to import into Segger Embedded Studio but rebuild come out error.
using the nrf52832_xxaa...
Hi all,
I would like to have a semi-duplex communication link over one pin (+GND). The nRF will act as a pure slave device which responds to, and acknowledges, commands...
Hello, we understand that the Nordic framework, by default, restarts advertising on disconnect. I learned that here, thank you:
https://devzone.nordicsemi.com/f/nordic-q...
I'm currently running on nRF Connect SDK (hash: 4b012fb4882f0ddd3de9f339ebc5a3f1c3cacd4a). I'm running a connection between a nRF91+nRF52840 (as central running NUS_C) using...
I have an nRF52840 board that fails to connect to Linux over USB. The board powers on and the green LED at the lower left of the PCA10056 flashes on/off rather quickly. But...
There is a bug in fds.c file, Please go through the below code snippet.
I do not return from fds_gc(), execution stays there for infinite.
More information:
1) #define...
Nordic nRF52840, with regards to stored security keys in flash, some wear leveling schemes move data when being updated but do not erase data from the old location. This is...
Based on several posts I've found on the forum, the notification queue size is automatically set by the stack based on the connection event length (NRF_SDH_BLE_GAP_EVENT_LENGTH...
Hello, I have developed a program that reads (with I2C) a temperature sensor and sends it to the central board. The central board is a NRF52480-DK. I have tested the peripheral...
Dear Sir.
I was testing dfu mode with an nrf52840 dk and held down the IF BOOT/RESET button, then powered up and waited a few seconds before it went into bootloader mode...
Hi,
I'm evaluating the NRF52832 for an ultra low power BLE application where I'm going to use GATT. I've built some prototypes with the NRF52832 and right now I have to...
