Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Hi. I have just installed the new windows nRF connect 2.6.2.
How do you do secure DFU? There are no apps in the list to do that. On your website it says it supports DFU...
In my attempt of learning the nRF52 "eco system" (nRF52 DK, nRF15.3 SDK, SES and pca10040e project for nRF52810), I have combined the GATT_C, GPIO and SPI examples to make...
Device/SW Info:
Ubuntu 18.1 SDK : 15.0 SD 132 v 6.0
NRF52832 QFAAE1
The device once connected to the device is immediately dropping the connection upon going into...
Hi,
I am using a sniffer on nRF52840 DK between by central and peripheral device. The frequency of packet transfer is at 433MHz. Can the sniffer detect the packets at the...
Hi everybody,
I am currently trying to write in flash several records key in a same file using fds_write, fds_update, fds_records_find.
My page is FILE_ID = 0x1000 and...
Hi,
I have an application which scans for BLE advertisements and pushes some information about it over UART.
I run this on a nRF52840 DK card using softdevice s140 6.1...
Now, I have a project that needs to do a master device to communicate with another slave device, but the slave device is done by the customer. I found that my main device...
Hi,
When trying to connect various thingy's to an Android with the Thingy SDK, the debugger gives me that :
D/BluetoothGatt: onClientConnectionState() - status=8 clientIf...
Hello ! So i have a nrf52 device, and i would like to know if there is a possibility to us it as a multi hub devices. ie: two nrf52 devices, one programmed with ble_app_uart_c...
Hello Everyone,
I am building an application where I have to change the scan window (BEARER_SCAN_WINDOW_DEFAULT_MS) in run time, based on a specific event. Does the stack...
I cannot find any useful information on the purpose of this project: examples\connectivity\ble_connectivity\pca10040e\ser_s112_hci (and likewise with other boards & SoftDevices...
Hi all,
I have a hard time to merge Mesh Proxy Service and Nordic UART service. I am working with mesh SDK v. 3.1.0 and nRF5 SDK v. 15.2, coexistence example ble_app_uart_coexist...
I am considering using BLE advertising for sensor devices as peripherals and using a mobile phone as receiving device.
Because the number of sensor devices can be more than...
The current protocol for the mesh serial interface as documented here:
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk%2Fdita%2Fsdk%2Fmesh_sdk...
how to program an nrf51822 chip(chip with ou coin cell battery the rectangular chip not circular) using nrf51-DK to work as a beacon .. kindly share me the detail process...
