Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Using this sheet
https://www.sparkfun.com/datashe...
I'm trying to figure out two things.
1) There is a section on timing but I'm a bit confused what SPI Clock rate...
Hi, I'm just a beginner with Bluetooth. I want to make a simple bluetooth module, so I just bought nRF52832 and other devices like capacitors, inductors, crystal oscillator...
Dear nordic,
I want to add long range in my application and also i want to set maximum power
i used sdk 15 and example ble central and peripheral(relay)
Where i set...
I have been working successfully on both PCA10040 and PCA10056
I want to work with NRF51822.
When I look at my sdk I see no folders for my PCA10028.
I see folders in...
Hello,
I have read numerous posts about NRF_ERROR_CONN_COUNT but yet able to solve this solve, my setup is NRF52840 Dongle as central and I want to connect to multiple Heart...
Hello! We are trying to transfer the data between two nRF52840 development kits through NFC. Is doing so possible without using any other reader hardware? If not, then we...
I am using SDK13 with a nRF52832 development board.
When trying to compile the Multilink central example with gcc and I am getting the following error:
../../../../.....
I'm just a bit confused on how gpio detect works. After setting the sense config for input I realize that a change in voltage will trigger a sense signal that will create...
I mange to identify and provision the Light switch example on the PCA10059 Dongle and fanstel gateway with no problems. IT use to work on my PCA10056 DK but has for some reason...
I am using nRF52 SDK v15.2.0, nRF SDK Mesh 3.0.0, and Segger v4.1.2.
I am trying to add the proxy service to the client node of the BLE_UART_COEXIST example. Has anyone...
Hello all
i have problem with doing this example
https://github.com/gamnes/nRF52832-buttonless-dfu-development-tutorial
Here is my stepts to do this
1.Download Sdk...
Hello
We start working with Zephyr and nrf52840. What is the right way to overwrite values defined in nrfx_config_nrf52840.h with Zephyr? The NRFX_CLOCK_CONFIG_LF_SRC is...
I was wondering what determines the logic level of the nRF52840 interfaces? Is it whatever you supply VDD with?
For example, if I supply VDD with 2.8V, will the logic...
