Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hello,
For my project, I want to develop a Zigbee coordinator for the Thingy:91 that receives reports from end devices and it publishes the values to the cloud. I've developed...
I am currently running nRF Connect Desktop App on Apple M2 chip (ARM64 ; 23.6.0 Darwin Kernel Version 23.6.0)
I have installed nrfconnect-5.1.0-arm64.dmg
Two major issue...
I can read above 3000 samples from accelerometer, before connecting to BLE, but after connecting to BLE the data rate reduces to 200 samples. This is clearly checked and identified...
I have been using VS Code and nRF Connect extensions for over 1 year. I run on a Mac Mini computer with Apple M2 processor. I recently updated the macOS to Sequoia Version...
I'm trying to build my project for nRF54L15 DK. The project uses mcuboot. When mcuboot is being built, I get following warning:
I guess the problem is caused by the config...
Hi, DevZone,
Our customer, Hosiden Osaka, wants to get the recommened foot print regarding nRF54L15, that is, the following each land pattern respectively;
- WLCSP 300um...
I am writing a program for the nRF52805 for use in a battery-operated remote. It needs to wake up from sleep when any button is pressed, perform the interrupt (blinking an...
I have found that in NCS SDK 2.6.2 it was very simple to enable FLASH_SIMULATOR as part of the mcuboot configuration overlays. But starting from SDK 2.7.0, I keep getting...
Hello.
I found this in the sx126x .c driver :
These lines did not allow adding more than one device to the overlay . I removed this code and rewrote all driver files...
example Matter_light_switch in vs code
version using nrf connect sdk -> v2.8.0
manage tool-chain version v2.8.0
nrf52840dk
getting error while building code
...
Hi,
I follow the execise https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-8-bootloaders-and-dfu-fota/topic/device-firmware-update-dfu-essentials...
Hi,
I'm trying to find the BOM referenced in the Hardware Design Guidelines for the nRF9151 under the Schematic Design section. According to the document, the BOM should...
Is there a way to obtain the Tx/Rx packets num in LE Audio? I want to calculate the PER in LE Audio. Using nrf v2.60, NRF 5340 Audio DK.
Thanks for your reply.
When configuration options CONFIG_SEGGER_SYSTEMVIEW =y and CONFIG_TRACING =y are added to my prj.conf the following build errors are shown:
followed by many other errors...
Hi,
I have a NRF52840 DK , I was using it for development. After one day the board don't turn ON anymore. I'm using USB cable as a power source. Acording to several subject...
