Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi. I have some question regarding to Bluetooth 5.4 on Nordic platform
1. Can Nordic platform do Advertising Coding Selection? I saw some old old issue that the device...
Hi,
I have tried to update the nRF Connect for Desktop app (v.4.2.0 to v.5.0.2). Unfortunately, the process does not work through the end. Once the installation of the new...
I have to use 240 bytes for my sensor value to send in bluetooth. so i choosed to work on ble_app_att_mtu_throughput i need only pheripheral to work on it . i have to remove...
Hi, I was wondering if hosting more than one nrf Connect for desktop version on the same computer was possible. The reason is that I need to use both the old app LTE link...
Hello,
I have connected a LSM6DSO sensor to my nRF52805 which is powered via GPIO. At startup zephyr RTOS wants to init the sensor and failed. After a reboot it detects...
On the SDK 17.0 NRF52840 platform, using sd_temp_get to read the chip temperature works correctly. However, if the sd_clock_hfclk_request function is used in subsequent operations...
Hello,
I'm trying out the example code "pin_change_int_pca10056". But the delay time between sensing a voltage change and toggling the output GPIO is quite long. 22us. Is...
I wanted to know in what ways can I connect thingy:53 to nrf9160 dk via Bluetooth? I understand that dk has onboard nrf52 and hence thingy:52 could get connected wirelessly...
Hi all, I am using the nRF52840 and I came across the nrf52_handle_approtect() func in modules/hal/noridc/nrfx/mdk/system_nrf52.c.
In the nrf52_configuration_249() function...
Hi,
I am unable to access P0.09 and P0.10. I face a similar problem to this thread . I've declared CONFIG_NFCT_PINS_AS_GPIOS=y in prj.conf. Also I've checked 0x1000120C...
i have a custom board that uses a nrf5340 that has been hardware modified so i can work again on getting my board to draw the mimimum power from the battery.
i have a PPK2...
I am using nRF5 SDK (17.1.0).
The MTU size is set to 53. I am using sd_ble_gatts_hvx() to send 16 bytes of data via Notification.
When I check the received data with the...
Hi,
Our product is currently undergoing FCC and ISED certification with Dekra. They are asking for 58741REM.001, 59675REM.001 and 64610REM.003A1 reports for reference. Can...
Hello! I am a newcomer to nrf and embedded programming (other than basic arduino and micropython projects). So far I have gone through many of the devacademy walkthroughs...
