Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hello,
With NCS v 3.2.1, I am working on a BLE application with nRF52840 dongle.
I was trying to add FOTA feature in my application by adding the following line to sysbuild...
I just ordered and opened up the nRF9160 dev kit from Digikey. I was going through the quick start and I named the device and when I went through the verification step, it...
Can you clarify, is it possible for the nPM2100 to set Vout < Vbat I.e. 1.8v out with 3v battery? The behaviour of the EV kit suggests not...
The datasheet isn't really...
We have a Thingy:91 (nRF9160) that we use for various LTE-M / NB-IoT network debugging. Until recently I was able to see both RRC and NAS messages in both " Cellular Monitor...
Hello,
I am developping an application based on ESB protocole using BT840NE module (nrf52840 + nRF21540) SDK 3.2.0.
on the PTX side, I am measuring the current using the...
Hello,
I am a developer/maintainer for the RF24 Arduino library at https://github.com/nRF24/RF24
I've found in some cases, the R_RX_PL_WID register returns 0 while the...
When updating from nRF connect SDK v3.0.1 to v3.1.0 we noticed a change in the clock_gettime() function.
In the old version, the clock was not reset by a reboot.
The new...
nRF5340 I2S MCLK issue – unable to get 12.288 MHz MCLK for 48 kHz sampling
I am using the nRF5340 SoC and configuring the I2S peripheral as Master to achieve a 48 kHz audio...
Hi,
I get a PCBA which contains the following test points of nRF54L15 : P0.02, P0.03, P2.07, P2.08. I would like to set one of them to be UART TXD.
In pin assignment...
hi support team,
customer is using mesh and met a problem, here is the situation:
1. customer using mesh/light as basic demo, adding mesh DFU function in it ,and deploy...
*** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr OS v4.1.99-ff8f0c579eeb ***
Hi,
I purchased several nrf54L15 development boards and am preparing to...
I'm trying to run a custom image on the net core. I've successfully done so using the following exercise in the intermediate course: lesson 8 exercise 2 however when trying...
Hello,
We have some hardware that uses the nPM2100 in roughly the 'one button' configuration where the SHPHLD signal is used for the reset button as well. When the reset...
Hi, We have a device already in production. We have an issue where the device fails to connect to an Android phone or iPhone hotspot with WPA3-Personal. We tried to change...
