HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
I've updated my project from 2.7.0 to the latest (3.4.1), which was an experience. However, I've got it compiling now, but I'm getting the following error in the SW PWM driver...
Hi there,
I was going through Nordic Semiconductor's Introduction to Bluetooth Direction Finding video. In one slide of that, host talks about area of coverage of Antenna...
Dear all,
is it planned to update the declaration of conformity of nRF9160 from EN 301 908-13 V13.2.1 to EN 301 908-13 V13.3.1?
EN 301 908-13 V13.2.1 is only valid until...
NCS: 3.4.0 Chip: nRF54L15 Hello, in the past months, there has been quite a change regarding Security and Vulnerability Monitoring on the Nordic Semiconductors side. I got...
Our company is developing second-generation implantable medical devices and plans to use the nRF54LM20A chip/component. We place a high priority on product reliability, so...
Hi
SDK: ncs-v3.4.2
I wanted to compile the lesson as a starting point for a product in non-secure mode with TFM.
I don't have the nrf5340dk but one with the same chip...
Hello Nordic Support Team,
We are currently evaluating and developing custom application firmware on the nRF93M1 DK (Hardware v0.4.0) using nRF Connect for VS Code .
Issue...
Title: nRF54L15: Stopping WDT (WDT31) in PM state entry does not decrease sleep current (~2 µA)
Device: nRF54L15 NCS / Zephyr Version: ncs 3.4.0 and zephyr 4.4.0
Description...
Dear Nordic,
Currently nrf7002 dts binding file for QSPI bus has an 'QSPI' label inside for [compatible, on-bus] scheme matching, This may cause problem on non-NRF host...
Our firmware currently uses Zephyr test USB IDs: VID 0x2FE3 / PID 0x0100 (build shows warning about it). These IDs belong to Zephyr and only for testing.
USB is used only...
What's the proper way to implement bonding that depends on proximity (rather than a whitelist)? So when the client (phone) is close (say, five to ten centimeters) to the server...
I'm in the early stages of building a Thread + CoAP low-power sensor and using the nRF54L15-Tag as a starting point. Using NCS, the lowest idle current I can get is 13 microamps...
Hello,
We are developing a product based on the nRF9151 and are preparing its CE/RED conformity assessment. We would like to leverage the existing nRF9151 CE/RED certification...
Hi Nordic DevZone,
We are currently looking at how best to handle nRF9151 programming in mass production, and I would like to understand Nordic’s intended approach a bit...