Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hello!
I've been investigating NCS for several days and come to the conclusion that we don't definitely have to use it for our developments. By the way, it'd be way too...
Hi,
I have a custom board with nRF52832 with external spi flash and I'm using SDK 17.1 and softdevice s132 4.0.5. I will use OTA-DFU to receive the new firmware image from...
Like several other folks, I have been attempting to replicate the results in the Matter webinar here , but updating to the v2.1.0 SDK and using the Nordic dev kits I have...
Hi ,
I am working on NRF52840 microcontroller, I want to implement blinky LED for P1.09 GPIO pin, can you please tell me, how to implement that.
Thanks
Hello!
The company that I work for has built a gateway that uses the nrf52832 as a ble central device (nrf5 SDK and the s132 softdevice). Customers frequently ask us to...
Hello Nordic support:
How to reduce nRF9160's LTE-M TX power in coduction test. Is there any AT command to reduce TX power? Or could you give us some guide about how to...
I am diagnosing pin malfunction in a custom board where I have working code from another version of the board which no longer works.
I am developing against NCS w/ VSCode...
Hi,
When asking to change the toolchain version in the VSC extension I get an error message:
Command 'nRF Connect Select nRF Connect SDK Toolchain' resulted in an error...
I am using the current nrf-sdk v2.1.0, which includes a Zephyr version (3.1.99 etc.) which has at the used stage an error with twister: instead of using get_testsuite the...
Hello,
I tried to run the sample Bluetooth: Periodic Advertising but I found some issue.
I'm using SDK v1.9.1.
The first issue was related to advertising creation with...
Before I go deep into the rabbit hole, I am wondering if anyone has had success with the following:
I am in a Windows 11 environment
I want to setup Docker with nRF...
Hi Community & Nordic Semi
I have an ultra low power design using the NRF9160.
I would like to avoid adding an additional LDO to reduce costs and Iq.
VIO from the datasheet...
Hello Community, i'm currently working on a custom board based on BC40C which is a BT/BLe module based on nrf5340 i'm trying to debug my board with jLink ultra + under, i...
There is an examples that show how to change from a 2Mb/s to a Coded 125Kb/s ?
May I change the bit rate of the comuniucation dinamicaly ? For examples I see that with a...
