Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello, guys.
I am using nRF Connect SDK, version 1.4.2 and nRF52840DK. I wonder what would be the way to print floating numbers during debug phase?
According to this thread...
Using the latest nRF_Connect_SDK
How can we set a udp/dtls socket, peer connect timeout for this call:
If there is no way to set a timeout for the call itself, is there...
Windows 10
NCS 2.0.0
We have run the Gazell samples successfully on the nRF52833 DKs. In these examples the CONFIG_GZLL_TX_STATISTICS is enabled (gzll_ack_payload_device...
Note: This might actually be a documentation issue more than a real problem because the build seems to work. But some clarification would still be appreciated.
We're developing...
I'm developing FOTA through LTE Modem which is made from QUECTEL(EC21KL)
On my custom board, nRF52832 is connected with EC21 LTE Modem via UART bus(TX : P0.16, RX : P0...
I am updating Nordic Thingy:91. I am following instructions on Nordic's DevZone web page: "Getting NB-IoT Demo running on Thingy:91
I have successfully updated modem using...
Hy
i am using a nrf5349 Dk board ,i am able to build and flash the board.
but when i am using this by building and flashing the board with hci_uart .in the linux system...
Hy ,
After i a buildng and flashing the hci_rpmsg as a cupapp . i flash the board
Then when i am checking the board with ubuntu laptop .i am not able to see the board...
Hi all!
I'm currently working on the UART on the nRF5340 board. The SDK describes three options: -polling API,
-interrupt-driven API,
-asynchronous API. With Polling and Asynchronous...
During development I noticed the following behavior:
If NRF_SDH_BLE_GAP_DATA_LENGTH=251 and NRF_SDH_BLE_GATT_MAX_MTU_SIZE=185, on Android devices the connection procedure...
Hi
For some reasons my Windows 10 laptop reports two JLink CDC UART Ports when I connect one of my nRF52SDK boards.My plan is to use this board with nrf Sniffer / Wirshark...
Im struggling here with porting my code from SDK15 to NCS 2.0.2
Im happily TXing data from NRF52811 via UARTE and receiving via FTDI to PC, but Im unable to receive any...
