Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello all,
I am porting the code from the nrf52dk to the nrf52820 based module and so far so good!
However, I can blink the LED on certain pins while not on the others...
Hi,
I am developing the nRF52833 DK with NCS v2.00.
I have implemented a service to display RSSI. I have setup the service according to the instructions provided by Nordic...
Hello everyone, I have an oxygen sensor"Gasboard-7500H" i need to read purity and flow with UART communication, this sensor works perfectly with Arduino and display corrects...
Hi,
I am developing an embedded system that uses Bluetooth communication and would like to manipulate certain Bluetooth characteristics such as TX power and RX sensitivity...
BLE Device
- nRF Connect SDK: v2.0.0
https://github.com/NordicSemiconductor/IOS-DFU-Library
This library doesn't seem to support the new nRF Connect SDK.
Which library...
Until 1.9.0 of NCS, SES was recommended, so it was possible to use OpenOCD from there. With NCS 2.x.x, VCS is recommended, so it's good to use it, but I want to continue using...
Hi,
We have some variables in shared memory. These variables can be accessed directly by both cores, and this is not controlled through IPC.These variables can be accessed...
Hi Nordic Team
Starting Point:
Provisioning of dimming server is done with code from the PB Remote provisioner, working so far.
Publish of model to group is acived similar...
Heyyy guys!
It is possible that I'm doing something wrong, but i'm confused as this was definitely not an issue at some point while i've been working with the 5340.
I...
Included "bsp.h" and "nrf_fstorage.h" still getting these below errors:
undefined refence to `bsp_indication_set'
undefined reference to `nrf_fstorage_init'
undefined...
Our product is using NVS to manage settings in external flash. The normal NVS initialization time is between 1 to 3 seconds at boot. Occasionally I have witnessed 10 to 15...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1
Normally OTA works well. I found unexpected assert after OTA is done. Can you please review my assert code with my elf....
I want to make a low power beacon with GPIOTE input which indicates movement and causing a change in the beacon advertisement (e.g. minor value). In order to do that I am...
Hi,
I am using Zephyr's sample code of sensors. Sample code is using wrapper function for device initialization, getting sensor's value etc. But there is no API exposed...
Hello! Just a quick question. I cannot find this file anywhere ` <InstallFolder>\examples\multiprotocol\ble_zigbee\ble_zigbee_dynamic_door_lock_nus`. This is referred to from...
