We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello,
I’m currently working on a hardware design using the following components:
nRF54L10 SoC
nRF21540 Front-End Module (FEM)
2450AT18B0100001E chip antenna...
I'm developing a project for nRF54 using NCS. I have a question regarding the placement of the BLE protocol stack. In the previous nRF5 SDK, the protocol stack was usually...
I have downloaded the nrf connect software and downloaded the segger drivers. I cant see the drivers in mi windows drivers administrator. The evk is powered by the usb because...
Hardware env: New designed board with NRF52840 + NRF9151, which 52840 connect 9151 via uart
Software env : NCS version: v3.1.0 (new installed) Nrfutil version: 8.1.0 (34e21a1...
Hey, since iOS version 18.6.2 the BLE connect to our BLE peripherial with nrf52840 getting disconnect events. Also the range between them is very bad. The connection parameter...
I'm currently working on some projects for the nRF54 platform using NCS and VS Code. I want to delete the unused files in my project because the codebase has become too large...
In the nRF52840 Product Specification PDF v1.11, on page 323, the third paragraph down states:
1. "If the CPU performs a clear operation on a bit in the LATCH register...
Hi Team,
below mention errors I am getting west build process.
* Executing task: nRF Connect: Generate config HVPP_BLE_Board_Files/nrf54l15/cpuapp for c:\Haritha\Github...
hi support team，
customer told me 54L15dk debug out is not able to program another 54L15 chip.
so i tried,
1. A-54L15dk debug out program B-54L15dk debug in, failed...
I'm trying to leverage the asset tracker project form nordic 9160dk to actinius icarus 9160 board, i use tagconnect 2030 to connect P19 of dk and icaurs, but the jlink cannot...
When I try to add OTA image compression for MCUboot, the RAM utilization skyrocks and is not compatible with the nrf52833. Is there any way to cut out any and all excessive...
Hi, I'm working on a product that uses nRF52840 (The custom board actually has the Ebyte module E73-2G4M08S1C). nRF5 SDK 17.1.0. The firmware consists of: 1. Bootloader -...
Hi, I'm using nRF9160 as an MCUmgr SMP client to download firmware via HTTPS and send it to nRF52840 (SMP server). Using SDK version NCS v2.9.1, I enabled CONFIG_NRF_MCUMGR_SMP_CLIENT...
