Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
I am noticing that particularly with the transmission of bytes over UART while scheduler is running, either some bytes go missing or the entire set of bytes aren't sent or...
Hello
Question: On what clock/clock-speed does the system tick timer run, when configured to use the external clock instead of the CPU clock?
I've seen a couple of...
Good afternoon,
I noticed in the nrfx driver folders there are two differente implementations for ADC: "nrfx_adc.c" and "nrfx_saadc.c"
What is the difference? Why two...
I had successfully interfaced lis3dh on nrf52 dev board using i2c protocol, i am getting raw values of x, y and z but i don't know how to interpret those values i.e. convert...
Hi,
Is there any similar to Online Power Profiler for Zigbee? How much my nRF52840 application should consume when using zboss stack? What is the minimum expected consumption...
Hi all,
I'am doing DFU via OTA
The device will be in bootloader mode ?
my current application has a thread running when i'am initiating DFU via OTA in nrf_connect app...
Hello !
I would like to evaluate few examples from standalone SDK and compile those under Linux Ubuntu.
For example : nRF5_SDK_17.1.0_ddde560/examples/crypto/nrf_cc310_bl...
Hi , I am working with NRF9160. I want to publish 3000 byte(char array) on mqtt server but I get Stack Overflow error. How can I solve these error? I tried these proj conf...
Hello! I currently have an external button and LED connected to the Icarus IoT dev board. For the time being, I just want to turn on the LED in the callback function when...
Hello,
I have a few questions about operation around the nRF9160.
I uploaded a minimal program on the nRF9160-DK card to obtain low consumption.
I get 600uA on average. In...
Hi,
I have implemented the USBD CDC ACM driver into my firmware. What stands out is the latency as soon as the event
APP_USBD_CDC_ACM_USER_EVT_PORT_OPEN triggers, my terminal...
hello. im having issues using ble uart, im planning on connecting my phone to nordic by bluetooth and to pc by usb, the problem that I have is when I use a usb port terminal...
Hi,
We are going through the errata file (nRF52840 rev 2) and wonder how to link anomaly (chip level) with nRF Connect SDK release (RTOS level)...
Where to find the...
Hi!
I am trying to interface LIS3DH module ( https://www.adafruit.com/product/2809 ) with nRF52 DK, SDK 11, via i2c/spi. I tested on Arduino UNO & it gave x,y,z values....
Hello, industry. Two questions for you:
1. To test fault-tolerance of our BLE scanning device we need to generate and advertise from another BLE device custom faulty ...
