Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
I would like to confirm how to make nRF5340 Audio stereo.
The nRF5340 Audio source is mono, and to make it stereo I believe that it is necessary to convert the data between...
I recently enabled power management in my code base by adding these two oiptions to my prj.conf:
CONFIG_PM_DEVICE = y
CONFIG_PM_DEVICE_RUNTIME = y
The code runs...
Hi,
I cannot bond to NRF5340DK running the `peripheral_ancs_client` sample if external oscillator configuration is disabled (thus using synthesized from HFCLK).
Environment...
Above is the trace and the commands inserted. We were unable to get a response using the at+cops? command. Both SIM cards were active that we tested. We tested band 12. Could...
I have a project that was building, but now on restarting VS Code, I cannot access the build configurations.
The list shows a configuration as present, but when I expand...
Hi,
I am using the nPM1300 in combination with a STM32L431KBU MCU.
Also the code from Nordic to communicate with the nPM1300: https://github.com/NordicSemiconductor/npmx...
I am new to the nRF52840 and the whole Nordic environment, so this may be a pretty basic question. I couldn't find any other blog entries that fit.
I am developing a manufacturing...
Hi, I have an issue I can't understand. I'm getting the TRICKLETIMEOUT (Trickle timer timeout) ERROR 64 from my nPM1300.
If I understand correctly:
1. Trickle charging...
Hi,
My nrf9160-DK version is PCA10090, 1.1.3, 2023.31
I am trying to test the esim, but the firmware tells me no simcard found. After doublechecking the esim soldering...
Hi,
We are using nRF5340 DK and the nRF Connect SDK Version 2.6.1.
We are experiencing an issue with disconnections. We use bt_conn_ref() when receiving...
Hello everyone,
I am having trouble using the bt_nus_shell.py script and a NRF52840 development board to send shell commands. I am trying to follow the instructions mentioned...
Hi, im working in a project with the nRF5340-QKAA and I need VDD as output 1.8V, for this reasoin I supply the uC with 3.6V on VDDH like this image:
this works fine...
I am doing DFU using nRF52832 board. Is it possible to update partial firmware?
For example, Is it possible to change only blinking LED without changing other stuff from...
Hello,
I'm transitioning from the old SDK to the ncs, and have been through the nRF Connect SDK Fundamentals and Bluetooth Low Energy Fundamentals courses.
With pairing...