Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hello.
We are developing a project for our own board. We took the blue_ap_uart example as a starting point. The example works successfully on PCA10040, but when transferring...
Hi,
I have a problem with my nrf dongle i have working example on the DK and i could not put this onto the dongle. I tried dedicated examples and they are not working too...
I cannot find this sample in nRF Connect SDK v1.7.1.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/central_and_peripheral_hr/README.html...
Hi, I tried httpsClient sample on nrf9160dk. It did not work because I can not change APN settings on proj.conf. I attached my screen. What is the apn config command on new...
I have a simple prototype platform that previously uses nRF51822 which is discontinued. Now I plan to replace the BLE module with nRF52833.
Previously developed firmware...
Hi everyone ,
I want to perform DFU of SD+Bl+APP via UART.
I use nrfutil version 6.1.3.
The Softdevice is s140_nrf52_7.2.0_softdevice.hex and the application is based...
Hello everyone, i'm trying to deal with the ACS714T sensor but i can't find any samples or guide through internet the communication need to be done through ADC and SAADC HAL...
I am using the nrfx_uart and need to disable the receiption. I call nrfx_uart_rx_disable. When done once, the receiption is not working anymore, even when I call nrfx_uart_rx_enable...
I am the digital pcb and fw designer on a project using a dipole antenna defiend by the RF designer ( I have read the posts discouraging that and have taken that into account...
I am studying the ble_beacon example among the examples provided by nordic.
I want to code the beacon's uuid to indicate the mac address.
I studied to find the mac address...
Hi team,
Note that nRF Sniffer already support nRF52840 dongle, but can that sniffer the BLE5 Advertising extension pack?
How to set the sniffer software?
Thanks!...
Hi,
I'm experimenting with the AoA locator receives IQ data on nRF52833 in ncs1.7.1. It worked well when the locator only received IQ data from one beacon. But when multiple...
Hiya. We're building a custom appliance on top of a Nordic chip that talks to an Android/iOS app developed with Flutter and a custom cross-platform Bluetooth plugin.
We...
Hi guys,
I tried to connect to nRF52832 using the app and it was successful. But when I directly use the BLE in the Android system(android 11) settings to connect to the...
