Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
I'm trying to duplicate the boot behavior of a Thingy91 on a custom board, i.e. SW4:BOOT and SW3:BUTTON on power up, but the switches available use different IO. I'm wondering...
Hello, I am pretty new to using the Nordic products and was wondering if there is a simply way to write a text file from the nRF52840 to a pc. The system is required to log...
Hi Guys,
I know there are a lot if topicks about issue with "sd_softdevice_enable". I read them all and nothing help me. I'm using Eclipse IDE.
Im using a nRF52840-DK...
Hello,
I have recently switched my OS from FreeRTOS to embOS. I am now replacing the SDK files so my project will not be using FreeRTOS. I replaced the file app_timer_freertos...
hello,
I am trying to learn how to use the nrf52480 dongle and am trying to run the ble_connectivity example. I built it using Segger as is, no changes from the pca10059...
Hi!
I'm trying to sniff BLE advertising traffic using nRF Connect for Desktop on macOS and a nRF52840 Dongle.
I am running nRF Connect Desktop 3.8.0 on macOS Mojave 10...
I have done everything to install the VS code, installed Connect, Toolchains, SDK, Seggers etc. as in the help, but this is the result in VisualStudio Code:
It just keeps...
Hi,
The following code has been working fine since it was taken from the examples (NRF52840).
We wanted to remove the app_usbd_event_queue_process() so we enabled these...
Hello,
I have beacon advertiser and scanner. Scanner is scanning the devices from around. But its not scanning the device that i used for advertising. On the other side...
Dear Sir,
for my nRF52840 application made with the SDK v17.0.2 and S140 Softdevice I'm adding the peer module to a peripheral device example (UART with SAADC with timer...
I was trying to create my own sdk_config based on "$NRF_SDK/config/nrf52840/config/sdk_config.h".
I noticed it contains both the "NRFX" config and "Legacy" configs.
For...
I would like to change the GAP_DEVICE_NAME defined in nrf_mesh_config_app.h by DIP switch. like "nRF5x Mesh Light 1" or "nRF5x Mesh Light 2"
I have modified the light_switch...
Hi everybody, i get this error on a nrf53 with hr_coded on network coded, and UART example modified with multilink and coded_phy, tested by me on an nrf52.
The issue is...
