We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hi,
my zigbee network for 120 sensors. if i declare 120 install codes then most of them don't work. The "zb_secur_ic_add" function works without error, "zb_secur_ic_get_list...
Hello!
Following problem:
I try to save 100Byte uint8_t messages in the nvs on the nrf9160.
Sometimes it works and only some moving logs come up and sometimes the following...
Hai
I have a requirement to download the FW application of NRF9160 M33 via serial UART. Is this possible?
So, which zephyr project am I to consider for reference?
...
Hi all,
looking for samples for using CoAP with DTLS 1.2 (PSK) on nRF9160. All the samples I can find are not using DTLS. Highly appreciate any hint!
Thank in advance...
After a painful sequence here
https://devzone.nordicsemi.com/f/nordic-q-a/80283/how-to-use-the-trigger-library-to-program-the-nrf52840-dongle
I managed to merge the projects...
Hi, We have firmware running on a 833 board, and we had noticed that connection times with a NodeJS central takes around 8-9 seconds. We thought that this had to do with the...
Hi,
We copied sample application from one machine to other and added the project in explorer in vscode
this project was having C++ functionalities
these C++ configurations...
We are using nrf52840 as a peripheral, Nordic SDK 15.3.0_59ac345.
We are experiencing issues in the field where users are unable to reconnect with our device from our app...
I'm facing various issues with nRF Connect for VS Code on Linux (Ubuntu 21.10): " Create a new application from sample " keeps the " Create Application " button grayed out...
I want to get the value of battery voltage using pin number with battery voltage monitoring function in nRF52840. What I tried was to use the function "nrf_gpio_pin_read(...
Hi,
I am getting started with an example in this YouTube tutorial .
I downloaded SES and have gotten the NRF51SDKv12.3.0 from the Nordic Semi website ( here ).
I don...
Hello NRF ,
How Do I flash my dfu bootloader ( merged with softdevice ) and my application hex from nrfgo studio ?
I am able to flash merged bootloader from go studio...
I want to know how to configure parity, stop_bits, data_bits, flow_ctrl parameters in UART in the xx.overlay file.
Although these parameters can be configured through the...
Hi
Nordic Team
I use ncs1.6.0, SES compiler.I have a very difficult problem:
Now I am debugging the 2.4g communication between NRF52833 and NRF24LE1. I set the rate...
