We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
I want to use the usb dfu along with the buttonless ble dfu, how can I do so? I want to use the usb to have dfu and also work as a vitual com port? Can I simple merge both...
Hello
Can you provide customer with the API of the attachment( nRF_DTM.exe application)? They want to integrate this application into their mass production tools.
Hi everybody,
I am working with two custom boards with nrf52840 chip, using the examples of UART central/peripheral.
I set power TX of connection exactly as the example...
I have got the nrf5340dk,then i using the SES IDE of windows。I open the sample named "peripheral_nfc_pairing sample",and build the solution,then debug it .After those steps...
I am attempting to advertise two sets, one using coded PHY and one using 1M, currently using the master NCS branch (post v1.7.0-rc2 tag). This is on a custom board with an...
Hello,
I have got the exact same issue as described here: https://devzone.nordicsemi.com/f/nordic-q-a/58275/zigbee-reporting-not-work-while-using-multiple-endpoints/236706#236706...
I'm running FreeRTOS with default tickless idle mode (CPU is woken up by SysTick interrupt) on NET_CPU core.
If the TAD_S module (Trace and debug control) is not enabled...
Hi Nordic team
Last week and before, I tried sdk connect v3.0.0 http_application_update example.
Everything was fine. Pressed button1 to download new bin file and then...
HI DEV
Currently we found a UART Frame error on customer product:
Application scenario diagram
Figure1
nrf52820 ,SDK17.02, softdevice:S132 , gap event length=6*1...
Hi! I'm new to zephyr and nRF boards.
I am trying to write a custom board using the nRF52811. When I try to build examples using the custom board using the command (syntax...
When I asked earlier, it was not possible to send HTTPS payloads greater than 2K due to the TLS secure socket buffer size limit. I see in the most recent modem firmware release...
I'm using nrfjprog version: 10.13.0 / JLinkARM.dll version: 7.50a to flash a firmware onto a custom PCB with nRF52840. Programming hardware is a nRF52840 DK. Our firmware...
Hi,
I am sensing interrupts on a pin using GPIOTE. I can see the interrupts coming on the oscilloscope. The firmware also detects the interrupts. However once I am inside...
Is the IXIT for RF of nrf52832 correct bellow? The test house said the value of inband image frequency should 4Mhz.
IXIT for RF
IXIT Reference
Identifier ...
