I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
It's been a while since this Java developer really understood EE concepts.
Could someone jog my skills and explain to me roughly what the different pin rive modes are,...
Hi,
I need to send custom messages to models on my devices and I need to use a vendor model like I've seen other people on this forum use. But when I load the nRF Mesh...
Hello,
We are interfaced the nrf52811 with LSM6DSO32 through i2c and LSM6DSO32 is connected to Auxiliary(Temperature MAX30208) sensor through mode 2 connection. here I am...
I am trying to learn to use the nrfx API to control the nrf5340.
My installation is the NCS 1.6.0 with SES on OSX
It seems like nrfx most of the API devices are supported...
I'm trying to find a battery for my application and I need to know the max (peak) current draw for the nRF9160. On page 63 of the user guide, the max is 435mA with the specs...
I have a function which writes data to the external flash which is using a FAT file-system further using block device implementation of the SDK. Whenever I am calling the...
Hello,
I am working on nrf5340DK board and with a sample example "central_uart" under ncs->nrf->samples->bluetooth & "peripheral_uart" from ncs v1.5.1. I wanted to send...
Hello,
I am trying to setup test environment using nRF9160DK(PCA10090, 1.0.0)
Dev kit is located in Montreal, Canada.
I started with nRF9160_DK_Getting_Started_Guide...
I am trying to update the bootloader using BLE DFU and it does not seem like the app is launching after the bootloader update.
I currently have an app that works with the...
Hello, I am developing a Zigbee OTA client / server application. My code is based on the example from the 4.1.0 nRF5 SDK. From the example I took only the code related to...
Hi,
What is the the status of android and IOS support of bluetooth 5.0 long range ?
It would be great if you can give us a list of device that support long range (of course...
Hi,
i have some issues with nrfutil, i can't properly perform an OTA DFU over thread, either nrfutil cannot find ncp.hex or it stuck in "thread DFU server is running....
Hi,
I made a project around the peripherial-uart sample with a custom board for a nrf5340 chip.
I work with win10, Toolchain nrf Connect SDK 1.6.1
I can build it and...
Hi,
I'm attempting to develop chip to chip communication where an nRF9160 acts as an I2C master communicating with an nRF52840 acting as an I2C slave.
I got reasonably...
