We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hi we are integrating a ANNA-B112 device from u-blox that use the nRF52832 core. The pin mapping for UART appears to be different for the Software (not open source) that they...
I have a general question that I haven't been able to clearly locate in documentation. How does the processor handle "traffic" jams from within the different app timers? ...
Hi everyone, so I have been trying to enable the nRF52840 to send notifications to the Nordic Connect app via a custom characteristic. The app can detect the custom service...
Hello,
I have an issue opening the power profiler kit 2 on my windows desktop:
Somethimes it works after restarting, but stops working after a few minutes.
After it...
With a baudrate of 1000000, when i transmit 2 subsequent packets (with ACK), i have to put a delay of 0.2 msec or more. Otherwise the second packet will get ACQ packet acknowledge...
We're trying to debug an issue with our nRF52 chip when pairing to some Android phones. On the nRF52 we are connecting to mobile devices by acting as a peripheral for the...
Dear friends,
I used a serial bootloader by this tutorial Secure DFU Bootloader over Serial Link (UART) , i can upgrade my application with the pc nrfutil tool, the nrfutil...
Hi sir,
I have a question for Bluetooth 5.1 single mode. As I know, above Bluetooth 4.0 has single mode and dual mode. Single mode only supports LE and dual mode supports...
Hi.
I'm newer on Zephyr.
I want to use the LOG Output.
LOG_DBG("main.c"); LOG_INF("main.c"); LOG_WRN("main.c"); LOG_ERR("main.c");
Everything works but the color of...
Hi everyone,
I'm developing a new application/product. It will feature a nRF52805 without the LFXTAL but with DC/DC support. I'm developing with the NRF5 17.0.2 SDK.
I...
Hello,
I am trying to commission a device running the CLI sample to an OTBR I configured following https://openthread.io/guides/border-router (the OpenThread official guide...
Hi
in Zephir nrf9160dk_nrf9160_common.dts the SPI pins are defined
&spi3 { compatible = "nordic,nrf-spim"; status = "okay"; sck-pin = <19>; mosi-pin = <18>; miso-pin ...
hello,
i am using nrf52832 with sensor which uses uart communication and using sdk 15.2 but i could not get my excepted values in rx buffer which is of 3 bytes and values...
