Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
I think this is a very simple answer but I can't find out where the file is to edit for this.
From the nRF Connect v3.6.1 - Toolchain Manager there is a drop down and "Open...
Hi everybody,
I have been reading the serialization documentation ( infocenter.nordicsemi.com/index.jsp and I am not very clear about some points.
What is it for and...
Dear all:
I want to implement FreeRTOS using NRFX, I checked the example and discovered that it uses the nrf_drv_clock... and thus it becomes a spaghetti with this legacy...
Hi,
I am working on a project that involves 2 nrf52840 DKs. One device will be running a ble application while the other device will be lookin, fetching and programming...
In SDK 1.4 we combined the udp and GPS examples and the result is unstable.
I think this could be because once enabled by RRC mode == Idle, GPS keeps going forever.
After...
Hi,
I have an issue with using the %XRFTEST command for TX testing on the LTE-M network. My setup consists of the nRF9160 DK (PCA10090) with the MFW 1.2.3 and a 1NCE SIM...
hello,
i am using two customised nrf52840 boards to get maximum range between the boards using this example https://github.com/NordicPlayground/nRF52-ble-long-range-demo...
I have update the SDK from version 1.4.2 to 1.5.0.
Suddenly i see that the hci_rpmsg is not build as a child image.
Which defines do i need to set for that now?
Hi,
Currently, we work on a project that uses:
nRF9160
Zyphre OS
Segger Embedded Studio for Arm (Nordic Edition) V5.10d
SDK v1.4
CONFIG_NEWLIB_LIBC=y
CONFIG_NEWLIB_LIBC_FLOAT_PRINTF...
Hi Team,
I am trying to build a project for nrf52810 and I selected an example project from the below given path.
nRF5_SDK_17.0.2_d674dde\examples\peripheral\blinky\pca10040e...
Hi, I've been working with the nRF9160 and at some point the logs normally displayed in LTE link monitor were gone. I've tried re-installing the Link Monitor but it didn't...
I'm trying to merge the ble_Central example project with ble_app_template project. I've added 3 Custom services in the ble_app_template project by setting UUIDs and trying...
Hello,
I am working on a nrf52833 custom board. Most of the time, the system stays in sleep mode, and periodically sends bursts of data via SoftDevice.
I try to configure...
