Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello
I'm having problem with UDP reception. I'm using nrf9160 with modem firmware 1.2.3, nRF Connect SDK v1.4.0, LTE-M.
I can receive UDP packets in the device as long...
Hi I am designing an intercom and I need help related to it. The following are the requirements of my project. I need an intercom module through which two-person can communicate...
Hi
Now I have a PCA10040 board and MDBT42Q board. I intend to transfer data between two boards via ESB TX and ESB RX example. However, with MDBT42Q I used nRFgo Studio to...
Hi,
We would trigger button to send zdo_mgmt_leave_req to coordinator for leaving the group.
When coordinator is not on power up, we would receive the 0xFF at callback...
Hi,
I want to calculate throughput rate using data that nRF52840 dongle working as sniffer captured.
Wireshark shows 'time' , 'delta time' and 'packet time'.
I think...
Hi,
I have serval questions about TX power settings.I wan to increase power to +8dBm,but the result is no effect.
1 Before reseting Tx power,call nrf_802154_tx_power_get...
Hi There,
Custom xamarin bluetooth app [using Plugin.BLE] is failing to connect to the device using ConnectToKnownDeviceAsync approach. User uses tap-to-pair and tries to...
Hi ,
We have a requirement to use the end device. The device should be an sleepy end device normal . When we want to transmit a large data to router , we want make this...
Hi Sir:
I am using SDK nRF5_SDK_17.0.2,the chip is nRF52810. Using the ble_peripheral\ble_app_uart.
The IO is using P0.6 as the BLE Uart's RX Pin,And P0.7 is used as BLE...
Hello, I was successful in using Arduino headers/ libraries to program my nRF52 DK, but now I am attempting to recreate the project in Segger V5.34 for MacOS for potential...
I want to use 52840dk to implement a file system to save some data. I am using NCS V1.4.99. I tried two samples , v1.4.99-dev\zephyr\samples\subsys\fs\littlefs and v1.4.99...
Hello,
I have just purchased a nRF9160 development kit and created a new account on the nRF Cloud website. I was following along with the getting started video for the development...
I have configure a authorized read from a service's characteristic as below .
void ble_band_ble_evt(ble_evt_t const * p_ble_evt, void * p_context) { ble_band_t * p_band...
Related to the following Q & A https://devzone.nordicsemi.com/f/nordic-q-a/70355/saadc_task_calibrateoffset
In the process of checking the operation, we created the following...
