Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
We've a custom board which has NRF52832 and Maxime. They are connected over UART. ( I'm using ble_app_uart)
What I want is transfer binary data between Phone and...
Hi, i am trying to understand the SDK 17 by building my own libraries such as interrupts, ADC, IIC or so on. I was doing well untill i come across with "LOG". When i look...
Newly purchased nRF51 DK connected via USB cable to a computer. Attempted to program firmware via BLE sniffer and an error occurred (image attached). Connected nRF51 DK does...
I am porting our firmware from SDK v15.3.0 to 16.0.0. I believe I have most of the changes in place as I am able to build the boot loader and get it to execute without any...
Hi
I'm trying to use Crypto but can't get started because micro-ecc isn't installed
The install instructions say:
Enter the subdirectory for the SoC and the toolchain...
I have been trying to bring up a secure boot loader for our product based on the nRF52832 SoC.
I have reviewed three SDK versions (17.0.2, 16.0.0, 15.3.0) and observe the...
Hi,
I know that the QSPI peripheral of nRF5340 allows to augment memory by interfacing an external SPI Flash memory. In addition to the internal memory, does DFU by FOTA...
I use nrf52840 dongle on windows 10 to connect to ble devices, I can connect and send msg to the ble device ,but I tried "att_res, data = self.adapter.read_req(new_conn,BLEUUID...
Hello Everyone,
I'm looking for an MCU that could be used as a master for SPI communication to supply the necessary signals (CS+, SCLK+, MOSI+) to a slave device (amplifier...
Hello,
I have migrated my codebase from v1.3.0 to v1.4.0 of the nRF SDK and have a strange issue now where the serial port is spitting out sleep debugging information in...
Hi,
The nrf52832 product spec shows all the clocks provided by HFCLK and LFCLK. But where can I find which peripheral is using which peripheral clock specifically?
For...
Hi,
I need to read some BLE characteristics presented by a commercial device nRF52-based, using my nRF52-DK, based on the nRF52832 and PCA10040. I don't have the firmware...
Hello experts,
I would like to get my mind clear on this.
I am using NRF52833 for our custom board we are using Zephyr RTOS (NCS v1.4.99) and IDE is segger embedded...
We need to accurately control the time when the Bluetooth advertising package is sent out, so that the two slavers can simultaneously send the beacon data to produce the signal...
Hi,
I am facing an issue when setting up advertising intervals (in connectable mode).
Whatever the value I enter I will always end up with an advertising interval of...
