Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hello,
I'm transitioning from the old SDK to the ncs, and have been through the nRF Connect SDK Fundamentals and Bluetooth Low Energy Fundamentals courses.
With pairing...
EDIT: Sorry to be posting a lot about my LIS2DH12 problems lately, as I'm advancing somewhat while I have open support threads. Newest thread is here: In preparation of this...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Hello,
I have an NRF9160DK board and a custom board running the SLM application that are exhibiting similar behaviour. Both boards work fine with the supplied iBasis SIM...
Hello!
I have a custom board with an nRF52805 on it and I am simply trying to run the Zephyr blinky example and verify I can see a GPIO toggling as my first step. I installed...
Hi,
I'm using ble_app_att_mtu_throughput to communicate some data from a nRF52832 to another one. I reached my goal (1.4Mbps) but now I would know what the two board communicate...
Hello, I am going through the Bluetooth Low Energy Fundamentals provided by Nordic.
My nrf 52840 dk could function fine after lesson1, but when I flash my board with the...
Hi,
after upgrading to NCS v2.7.0, I have some trouble with an increased sleep power consumption of our device when I use Zephyr's gpio-keys for the button input.
I was...
Hii,
I am working on DFU OTA using nRF52832 board. I have created rsa-2048 key file (priv.pem) and saved it in my project folder and also, edited CMakeList.txt of project...
Hello,
I am currently programming using SPIM+Timer+PPI(via nRF Connect SDK v.2.6.1), but due to my lack of understanding, handling handlers is challenging. Therefore, I...
I have seen a few posts including:
Change advertised name (Bluetooth) - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com)
NCS bt_set_name() - Nordic Q&A...
Hi Folks, I’m working with an I2C LCD rated for up to 50KHz and it is showing a fair number of glitches. Can anyone tell me how to lower the I2C speed from the default values...
I am using an NRF52840DK.
1. I erase the chip to start clean:
nrfjprog --eraseall
2. I flash the MCUboot bootloader:
~/mcuboot/boot/zephyr$ west flash
The output...
We have a product based on the nRF52840 which uses the GC9A01 display driven using SPI on battery power. The device also functions as a Bluetooth connectable so it is normally...
Hello DevZone,
I am using a nRF52840 with sdk 17.0.2 with Windows 10
I am trying to setup a connection to my Windows PC but I noticed data fragmentation and a queue...