We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hi,
We built the Blinky sample with NRF Connect SDK 1.3.1. It works fine on NRF52833 DK, but when flashing on external custom NRF52833 board the firmware won't start without...
Hello,
I am trying to integrate the Unity test framework into our project and running into issues with how to add additional test files. Nordic provides one example project...
Hi,
I am developing a project where I have NRF52840 as a device and another NRF52840 as a BLE USB dongle connected to PC.
I have to improve the BLE data rate between the...
Hi,
I have a NRF52840 device connected by BLE to another NRF52840 BLE USB dongle connected throw USB to a PC application.
I want to synchronize the RTC on the connected...
Hello I am currently working on a project with the XM122 / XB122 kit for an evaluation, the XM122 card integrates an nrf52840 MCU and a radar sensor;
The goal of my project...
Hi, I'm using nrf52833 with SDK 17.0.0.
I want to send SAADC data over BLE.
So, I want to see data in my phone.
I've modified codes.
I want to use macro(ble_nus_data_code...
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/simple-application-level-authentication
Hi
I am looking to make this example work but this post is old...
Hi all,
we are now using nRF52811 and its SAADC. We would like to use the oversampling functionality, but there is some information missing in the datasheet.
So, when...
Hello,
nRF5SDk16.0, Softdevice v.7.0.1, device nRF52840.
We using manufacturer specific information in the advertisement data. Here are the set values:
The data is...
We have a PCB production with bug where AC13 (P0.18) accidently has a via shortenede to GND plane on internal layer. Thus nRESET is stuck low and cannot be pulled high without...
Hi,
I modified the LBS service to experiment sending more than a byte of data.
On the peripheral side, modified from ble_peripheral/ble_app_blinky
typedef struct { uint8_t...
I'm using visual code for my development. I've tested a basic hello world app, this works fine so c/cpp is correctly installed.
I'm now testing a basic app, but I'm getting...
Hi Team,
For our development we are using the nRF52840 soc, We need the some example code or some project which will explains the Usage of RSA algorithm and supported API...
Hello,
I am looking at the ble_app_buttonless_dfu/main.c
This implementation is initializing the queued write module. Is this required now for DFU operation? We currently...
