Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi Nordic Team,
I am currently developing applications for custom boards using the nRF Connect SDK v2.6.0, focusing on the nRF52840 microcontroller.
In our ongoing project...
Hello,
I am using the nRF54L15-DK development board running the official hci_uart example as the BLE controller. My own Linux system acts as the host using BlueZ to control...
Hi Nordic team,
I noticed that when using the external FEM (nRF21540) with the nRF54L5 device, the power consumption at a transmit power setting of 8 dBm is significantly...
Hi, I have implemented a soft UART in the VPR FLPR. I am having trouble power managing it. I see an unexplained extra 500 uA current draw after I start the CPR until I reset...
Hi, for nRF52840 raw proprietary RADIO mode, do TXADDRESS and RXADDRESSES imply a hard total node-count limit for a custom multi-node network, or only a simultaneous hardware...
SDK is NCS2.9.2,My device supports master-slave integration. As a slave, it can pair and bind with a mobile phone. As a master, it can scan and connect to two slave devices...
HI
I’m doing secondary development based on periodic_sync_conn in NCS 3.2.1 .
After establishing a periodic advertising sync, I have two issues:
Sometimes the buf...
Hello,
I'm trying to set up auto-provisioning and onboarding in my project as described in this sample: https://github.com/nrfconnect/sdk-nrf/blob/066ac6f61fe19ad91d805fd788d782e245f09a2e...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
On nRF5340 with external flash (SDK 3.2.x), is it possible to both support serial recovery enabled for both cores while supporting simultaneous DFU?
It seems like...
Hi,
i am developing under ncs 3.2.3 (then toolcahin 3.2.3 -> nrfutil-device 2.17.1).
FLashig OTP registers using batch method, i am getting the following "error" on nrf54l15dk...
Reference: first consult as Case id. 305571 Replyed by Tobjorn
I have a working proyect in wich 485 cable communication was replaced with NRF24L01+ but I need some help...
In the enqueue function esb_write_payload , the enqueue implementation uses ++tx_fifo.back .
In the dequeue function esb_pop_tx , the dequeue processing also uses ++tx_fifo...
I'm working on a project where we're planning to use XIAO BLEs on an OpenThread network, for that we need very low power consumption. I've been trying samples to get low consumption...
Hello, I have followed the guide to do a serial recovery of the appcore and it's working fine. Now I would like to be able to update both the appcore and the netcore. I have...
