Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hello,
I successfully downloaded SAADC SDK example in the peripheral folder. The hardware setup is as below ,
The pin configuration for this is as below
...
I tried implementing
https://github.com/andenore/NordicSnippets/blob/master/examples/temp/main.c
But i get 2.6V without connecting any of the Analog pins.
Exactly...
I have attached an Arduino INO file that I wrote early on in a project. It runs a probe. It is an amazingly simple probe but especially important. I am making a simple opacity...
Hi Team,
I planning to use vibration motor with nrf52832.
vibration motor will give maximum buzz on 20.3KHz(50 duty cycle).
So my question is
- Can I achieve 20...
Hello I would like to use the extended advertinsing packets from Blutooth V5 as used in the "ble_app_rscs" example. My problem is that I can't connect via the extended advertinsing...
It looks like NRF_LOG_INFO doesn't copy the data that is sent to it as per the below example. Is there a way around this so that I can reuse long buffers that contain either...
Our purpose is to integrate BLE 5 in our embedded application, and do it quickly.. We basically need to send/receive data with maximum throughput.
Per thread below, we are...
I am having some issues bootloading the dwm1001 board.
I am able to flash over UART and BLE using nrfutil and nrfConnect with:
s132_nrf52_6.0.0 softdevice
pca_10040...
Im trying load a TWI sensor custom built with LIS3DH, and it is showing following error.
The xml file looks as below
Can you kindly guide me, how to resolve...
Hello. I'm trying to create a new project or open existing examples with eclipse.
I tried to import "Existing code as Makefile project" and File->New->Makefile Project with...
I would like clarification on the use of the nrfConnect programmer for RE-programming the "dongle" a.k.a PCA10059. NOTE: NOT "programming a virgin dongle" Reference: The user...
I'm having trouble with certification in China. Here is what they are getting for spectrum using the nrf52832 with the nrf_radio_test_example. The lab is saying that this...
Hi,
We need send packets continously, and need adjust TIFS slightly when real packet interval is shorter or longer than expected.
The radio shorts register is set to RADIO_SHORTS_READY_START_Msk...
I tried implementing the custom BLE example in the below link Im facing two problem 1. ble_cus.h header file throws error
Main
ble_cus.h
ble_cus.c
The error...
I have just integrated the Buttonless DFU example code into my project and I am able to successfully update my device using nRFConnect. I'm using the NRF52840, S140, and SDK...
