Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi,
I'm trying to run the gps application off the master branch on the thingy91 and it dies like this:
It's built using the Nordic SES on windows.
Any ideas? ...
Hi all,
I am trying to connect to device with specific UUID. I am not sure what have I managed to do, below are some logs from NRF Log.
Did I connect properly?
I am...
Hello,
I am trying to run the mbdedtls example of random number generator shown here https://tls.mbed.org/kb/how-to/add-a-random-generator
I added MBEDTLS_CONFIG_FILE...
when i change the baud rate to 115200 my uart (Rx and TX) are giving me garbage out put.
so what do i need to change in my code(ble_app_uart example) when i have plan...
Dear Support / forum,
After reading the user and API guides, browsing other posts, and playing around with the ack-payload example, I think I now have a pretty good understanding...
Hi,
I am having a issue with building an application in IDE for nRF9160
Application : Asset tracker
I have been able to build this "problemfree" before, but this morning...
Hi~
I am developing door sensor system using nRF52840.
Currently for power consumption, sensor (nRF52840) is system off(NRF_POWER->SYSTEMOFF=1).
nRF52840 can wake up...
Hi, I have 8 peripheral devices each one has at least one sensor attached to it( peripheral will be nRF52xx), the sensor has a sampling period of 8ms. I will be using android...
Hi,
In BLE mesh v3.1.0 I see a file debug_pins.h. For what these debug pins are used and can I disable it for my custom board?
And one more thing related to PA and LNA...
Hi,
We are currently developing a Sensors/USB/BLE/LTE-M1 product for a customer. The board is equipped with one nRF9160,for cloud communication, and one nRF52840, with a...
Hello, I am using nrf5832 with SDK 15.3.0. I want to filter peripheral device based on mac address. I modified example code "\examples\ble_central\ble_app_blinky_c\pca10040...
I'm facing problem when I want to stop receive task, event EVENT_RXTO came at long time period. 4 to 5 baudrate bytes.
Is trere any documentation where could read time between...
Hello,
I want to develop a data transfer service which has a control characteristic that is used to write commands on the phone app and if the command matches any command...
In our application we have made a connection between two nrf52840 devices. with softdevice 6.1.1
normally we operate in 1Mbit mode and tx power on 8.
if we change from...
Hi,
After sending a few textmessages from the client to a server (8 bytes long approx. 10 messages/sec) i get a mesh assert on the client sometimes:
0> <t: 205648>, app_error_weak...
