Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
As a final step to the legitimate dual bank-based application DFU , the existing application will be replaced by the new application.
What happens if an internal error...
Hello,
Is it somehow possible to output a 13.56 MHz signal from the nRF52 ?
Yes, I KNOW: Similar questions have been asked many times. The nRF52 cannot drive an 13.56Mhz...
Hi,Nordic Teams:
I have emergent proble ,can you help me?
1.in light_switch example provisioner,there is some code below:
2.when provisoning ,we can setup a node to...
So I run SDK 15.0. I have a notification channel, and I want to transmit some data on it.
I run this code
hvx_params.handle = gatt_notify_handlers[index].gatt_handle;...
I'm using the nRF52840 to interface with an existing 802.15.4 network. For reasons decided long before I became involved, the messages exchanged are MAC command frames, not...
Hi,
I am testing BLE throughput between NRF52832 and iPhone XR using S132 stack. I am able to get maximum of 400Kbps. Is there a way to achieve throughput better than...
Hi,
I am trying to design the transmission lines based on the reference board design from Nordic.
I opened up the Altium layout file for the board which I downloaded...
I'm trying to communicate with HTS221 sensor and read WHO_IM_I but then I always get error 17 on nrf_drv_twi_rx and receive 0 on output
Twi init
ret_code_t ret;
const...
Hi
I want to use TWI read temperature from sensor Si7050, but i got a problem that doesn't jump into twi handler event. Can anyone give me some information? Thank you. ...
Hi,
This is somewhat tricky question..
Does GAP broadcaster differ with the BLE device which advertise packets with non-connectable option?
Is The device which operates...
I read the specifications on nRF51 series and the spec say that Bluetooth 4.2 with 2Mbps. However, standard Bluetooth 4.2 only support maximum 1Mbps bitrate.
First, I wonder...
So I added a header files folder to my project and then added a header file. The project would no longer compile after doing so. To troubleshoot, I changed everything in my...
Hello,
I am trying to upgrade my working projects to SDK15.3 from SDK15.2. All projects work except the bootloader project as there are significant differences in 15.3...
Hi,
If I understand corrctly, the flag CONFIG_NRF_CLOUD_PROVISION_CERTIFICATES=y should only be used once,
after that, the certificates are saved inside the modem.
...
Hello.
We are developing a device that require a 1Gb qspi memory interafaced with a nrf52840.
So far the qspi driver and the memory inits and the memory respond to some...
