Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hello ! I encountered a problem in sending and receiving data from one nrf51 card to another nrf52 card
i use this method in (ble_config.c) to send string data :
void...
Using the nrfx_qspi driver, it is possible to put a QSPI memory into DPM to save power, this all works fine and well. We want to keep the memory in DPM when uninitiating the...
Hi all,
I make a key using nrf52832. It tranfer data to other device. I have 2 option for this. Using beacon (BLE) or Enhanced ShockBurst (ESB) . I want to optimize energy...
Hi,
I was wondering what are the main differences between the different libraries included in the SDK that are meant to be implementations of ring buffers. I'm talking specifically...
Hi
I am developing a product for the health care market, and we chose embOS by Segger to by our OS for the nRF52840 Based product.
I've created a project based on ble_app_uart...
I am trying to send some data from RPi , And I am using the example of NRf Uart APP.
printf("\r\nUART example started.\r\n");
while (true) { uint8_t cr; // printf(" \r...
Hello All.
I try to build a generic function that read device reg over its I2C. I take the TWI master example of Nordic.
There is need for callback function to get in...
Hi
We are using your product nRF51x22_QFN48 with a balun BALF-NRF01E3 from ST and the PA.11 antenna from Taoglas Ltd.
Do you already have this product certified for RED...
Hi guys,
We have noticed some unexpected behavior of supervision timeout in case of few fast sequential calls of connect and disconnect commands in nRF connect app with...
hi...
i am using nrf52382 segger 15.2 version , i am facing issues i couldn't able to send the data ,here i am advertising using condition if my condition satisfied start...
Hello,
I use SDK15.2, SES4.12 and custom board with nRF52840.
I have a strip of ws2812b LED's connected to my device. I've made a simple RGB animation, each frame of which...
Hi,
I've been testing the sample code at_clent with Verizon wireless. I can send AT command to the DK via nRF Connect "LTE Link Monitor".
Q1. run AT%XCBAND=? to print...
Hi ,
I found nRF24LU1+ build in AES co-processor, but I cannot found the processing speed (the time for finish one AES processing) on datasheet.
Because my customer...
