We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello everyone,
right now I have two BMD-340 Evaluation Kits which used nRF52840 module and I want to evaluate Bluetooth Long Range and Data Rate of this module. I used...
Hi
I saw a fail for RF-PHY/RCV/BV-29-C on nRF52840 DK.
But I also find it is a known issue as "Anomaly 172 Addendum".
In the nRF52840_Rev_1_Errata_v1.2.pdf, two workarounds...
Hi,
I'm working with the nrf52840-DK and using the nRF5 SDK v15.2.0 Stack version.
I´ve got a working program for my coordinator (C) and my end device (ED). The C establishes...
Hi
I have this code that works like a charm when the device is connected and I want it to leave the network.
But if the device is dead or disconnected and I want to remove...
Hi,
I know this is a license question and the default answer is "contact a lawyer if you don't understand the license". But this can hardly be the first time someone...
Hi,
I'm trying to connect nrf52840 to IOS 12.1.4 as a Braille display. Standard BLE HID is working well, but when I try to connect as a Braille Display ( Settings/General...
I am trying to connect and according to the spec sheet, there might be multiple pipestatusevents.
When I try to connect using different phones (with different Bluetooth...
Hi,
I'm using the light switch client example to test the Mesh App on iOS.
The PCA10040 board can be identified through Mesh App, but not be identified on our test board...
I am using nrf52810 chip without softdevice or bluetooth stack. I started to develop at November 2017 with Datasheet version v1.2. On 31. Januar 2019 Nordic released a newer...
Hello,
I have project for collecting temperature information from 15 pcs temperature sensor.
It is possible to create system with 16 pcs nRF52840.
one of them will be...
Hello,
I’m using two nrf52832 as servers sending 20 Byte data with 18 ms notification interval.
Notification Data:
[incremented uint8_t ] [19 byte data]
Client:...
Hi,
I'm working with the nrf/samples/nrf9160/at_client (@ tag v0.3.0) with a PCA10090 board.
I had a question about the response to the AT+CESQ command.
Specifically...
hi,
i am quite new with programming tools like the nordic thingy and i am currently trying to get some initial program running, i.e. the blinky example. i have a few questions...
