Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Using this sheet
https://www.sparkfun.com/datashe...
I'm trying to figure out two things.
1) There is a section on timing but I'm a bit confused what SPI Clock rate...
Hi, I'm just a beginner with Bluetooth. I want to make a simple bluetooth module, so I just bought nRF52832 and other devices like capacitors, inductors, crystal oscillator...
Dear nordic,
I want to add long range in my application and also i want to set maximum power
i used sdk 15 and example ble central and peripheral(relay)
Where i set...
I have been working successfully on both PCA10040 and PCA10056
I want to work with NRF51822.
When I look at my sdk I see no folders for my PCA10028.
I see folders in...
Hello,
I have read numerous posts about NRF_ERROR_CONN_COUNT but yet able to solve this solve, my setup is NRF52840 Dongle as central and I want to connect to multiple Heart...
Hello! We are trying to transfer the data between two nRF52840 development kits through NFC. Is doing so possible without using any other reader hardware? If not, then we...
I am using SDK13 with a nRF52832 development board.
When trying to compile the Multilink central example with gcc and I am getting the following error:
../../../../.....
I'm just a bit confused on how gpio detect works. After setting the sense config for input I realize that a change in voltage will trigger a sense signal that will create...
I mange to identify and provision the Light switch example on the PCA10059 Dongle and fanstel gateway with no problems. IT use to work on my PCA10056 DK but has for some reason...
I am using nRF52 SDK v15.2.0, nRF SDK Mesh 3.0.0, and Segger v4.1.2.
I am trying to add the proxy service to the client node of the BLE_UART_COEXIST example. Has anyone...
Hello all
i have problem with doing this example
https://github.com/gamnes/nRF52832-buttonless-dfu-development-tutorial
Here is my stepts to do this
1.Download Sdk...
Hello
We start working with Zephyr and nrf52840. What is the right way to overwrite values defined in nrfx_config_nrf52840.h with Zephyr? The NRFX_CLOCK_CONFIG_LF_SRC is...
I was wondering what determines the logic level of the nRF52840 interfaces? Is it whatever you supply VDD with?
For example, if I supply VDD with 2.8V, will the logic...
