I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
How to configure an app_timer in counter mode. i just want to count number of pulses in pwm using app_timer. i didnt find any example in which app_timer used in counter m...
I'm trying to use fstorage module for event logging; several pages are used as a large circular buffer. When logging wraps from one page to another, the new page needs to...
Hello every!
I was developed my aplication base on nrf52 SDK (version 14.0). I am confused about SDK_config.h file. I can't cognize which macro should be 0 or 1. Example...
Hi all,
we are using the Nordic Uart Service in our product and Id like to connect our hardware to a Linux powered PC. Does anyone know how much effort it would be to make...
Hi all,
I have a working ADC implementation (S130 + Application) and use it to measure an analog input continuously.
However if I use the same code on top of bootloader...
When I have a test using nRF24l01+ with STM32, I can only get a playload datarate no more than 450kbps using nRF24l01+ 2M mode.
How can increase the playload data rate and...
I have been using two NRF24L01 to communicate with each other using just simple Arduino Uno Board.
it worked for 5 days and now all of a sudden it is now working.
I tried...
Hi,
in order to add flash programming support to the iSYSTEM toolchain based on a
customer request I would need a flash reference driver/monitor implementation.
Would...
The sync time for my nrf2460 seems to be about 4 seconds. Is this normal? Secondly, once
the pair is synced at close distance, one or two feet, as I move away sync is lost...
I'm planning on having all of the different Device Information Service characteristics (fw_revision, sw_revision etc) with each being just a single integer for version number...
Can someone tell me what these errors actually mean
JLinkARM.dll CORESIGHT_WriteAPDPReg returned error -1.
JLinkARM.dll CORESIGHT_WriteAPDPReg returned error -102.
...
I am using nrf52840 central and nrf52840 peripheral device. Ble communication is enabled between and data transmission is working. I would like to analyse the packet loss...
Dear community,
I have your Thread example set up with 3 nRF52840 Preview Development Kit. nRF Thread Topology monitor 0.8.0-1 runs fine if I download CLI-example onto...
I use NRF52832 and sdk13.0.0 to develop my own application. I want to generate 1000 Hz Timer to trigger the ADC. I use the timer 1 to generate 1000 Hz. But when I use GPIOTE...
