Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi
I am using nrf52840 in my custom board. I have a gpio button which is assigned for as a factory reset button. So when i press the button the whole board needs toi be...
Hello,
we are looking to develop multiple BLE audio source which sends the mic data to the receiver and the receiver receive the audio data from multiple transmitters...
In my design, I aimed to isolate the USB interface. To achieve this, I used the Analog Devices USB isolation chip, ADUM3160BRWZ, to isolate the connection between the PC and...
When I need to switch between 1M and 2M
I create an object of the type bt_conn_le_phy_param and fill in the parameters appropriate to the radio mode I want, and then I call...
Hello,
I would like to know if the nRF9151 is suitable for building a product that will be able to monitor (read) multiple pulse signals originating in utility meters (electric...
We are using nRf5340 and nRf7002. In our application , we are connecting wifi and goes to ksleep for few minutes.
After wake up from the sleep. wifi is not reconnecting...
Hello all,
I ported an old nrf5 application from SDK 12.3 to SDK 17.1. It uses S112 7.3.0 and FreeRTOS. Unfortunately I am getting time variant softdevice hard faults at...
While testing nRF FOTA download library we noticed that it supports only one image update at a time (download image, then reboot).
Irrespective of the image (either application...
Hello, I just upgraded from SDK v2.5.0 to v2.7.0 and now I have a problem updating the bootloader.
In my project I have b0, the mcuboot (in s0 and s1) and the application...
Hello, I followed Getting started guide for the nRF54L15 PDK ( Getting started with the nRF54L15 PDK (nordicsemi.com) ) and bumped into a problem when i try to build "hello...
I am using the following example as a reference for setting the TX power in a peripheral Bluetooth connection: https://github.com/nrfconnect/sdk-zephyr/tree/v3.6.99-ncs2/samples...
Hi, we are doing testing with a Nordic dev kit and looking for ways to check the status of GNSS.
We are becoming familiar with the XGPS command and notifications: docs.nordicsemi...
How can I return from k_sleep (or any other "sleep" method) when an interrupt occurs?
I would like my device to sleep (low power) until a GPIO pin toggles, then wakeup to...
Using nrf5340 DK with v2.7.0 SDK + toolchain. Blinky app works fine. Tried the sample apps:
- peripheral_hr
- peripheral_ht
Which both reproduced the exact same error...
