Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello,
I'm using nRF9160 as a HCI host and nRF52840 as HCI controller (nRF52840 config is based on HCI lpuart example). My application receives data over Bluetooth using...
We have two cases where the modem has downgraded itself from version1.3.2 to 1.3.1.
1. In the first case, due to water ingress, it appears that the reset pin has been toggled...
System: Windows 10, Vscode + Nrfconnect
I saw a previous post on same topic which fixes the issue by changing the settings in extension like said here ( changing extension...
We have pre-production product (based similar to the NRF9160dk setup with a NRF9160 (LTE-M, GPS) and a bridged NRF52840 (BLE). We are working through certifications for CSA...
Hi all,
I am aware of the different access port protection mechanisms (listed in my previous ticket here: Link ). I did also test both revisions successfully:
For...
Hi.
In our private network we experience one problem.
We can ping Google (8.8.8.8) via APN customer4. In Wireshark traces it is seen that ping is initiated.
On RRC level...
In our current development we are using NRF52840DK and the external memory MX 25R6435F. We are using Settings API to store some configurations on the external memory partition...
Hi, I have the structure for a Vesper VM3011 MEMS microphone:
In the 'overlay' file, I define it as hardware:
When I retrieve the properties from the '.c' file...
We are currently working on a project that has these requirements:
BLE Audio (Broadcast)
BLE Central and Peripheral
WIFI 5/6 (5gHz and 2.4gHz)
BT classic would be...
Hi,
I am currently developing a long range bluetooth module with the U-Blox NINA-B31 BLE module, based off the Nordic nRF52840 chip. I have come across an issue which I...
So, I have built prototype boards using nrf9160, flashed, they are working fine, now need to add to nrf Cloud and realized there are few ways to do that, all are not well...
Greetings
I am going through the BLE fundamentals course and I am doing exercise 1 of lesson 4, creating a custom service. From this exercise, creating the "LBS" service...
Hello,
For context, I am using an EVK-ANNA-B112 development board which has an nRF52832 inside. The development board has an external 32.768KHz HW clock connected to the...
Hello,
I am using sd_rand_application_bytes_available_get() in nrf_drv_rng_bytes_available()
A first generation of randmon number is made without problem.
But 5...
Hello
I have a BLE project using the nRF5340-DK and I wanted to use the nRF21540-EK for increasing range. My plan is to connect the SWF connector to the nRF21540-EK using...
