I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello,
I have custom hardware running on nRF53 and there are multiple sensors connected with it for the measurement of their different entities. The hardware is battery...
Hello Experts,
On my Windows 10 PC, I have installed nRF for Desktop v5.0.2 and J-Link Pack version 7.94e got installed along with it.
Also installed Nordic command...
I use nRF52840DK and nRF21540EK to develop BLE programs, and the program uses FLASH for BLE image storage, the program works well on the DK. However, when I burned it into...
Hello,
I try to flash my bmd-345-eval board with nrf connect visual in VS code.
But the connected devices don't show mcu but show VCOM0 and RTT on nRF connect in VS code...
Hi
I have a issue, I have 4 samples nrf9160 module, all run in same firmware with FOTA feature
I found that only one module cannot start FOTA, then I try to read message...
I am getting the following build error for a Nordic nRF5340dk
c:/ncs/toolchains/ce3b5ff664/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm-zephyr-eabi/12.2.0/../../.....
Hello,
We have an issue regarding PSM availability when roaming. Some operators do not grant PSM and once a device connects to such a network, it would drain the battery...
Hi, When performing GATT discovery on the peer device I observe that the procedure takes too long about 5-6 seconds even at the lowest connection interval. The same process...
I was trying to add the nrf91-modem-trace-uart snippet to my build configuration. I've found that it does not take effect when using the "Add Build Configuration" UI in the...
Hi support team
If I want to implement update advertising data dynamically function, which method is recommended?
1. bt_le_adv_stop (); and bt_le_adv_start (adv, ad, ad_len...
Hello,
I am primarily an STM32 user, delving into Nordic. I will be creating a product using the nRF52832. I would like to measure the 32MHz & 32KHz clock inputs to the...
This is a request regarding modules that can be used in Pakistan. We think that nRF9160 is matched for this requirement. Could you please tell us whether nRF9160 is okay or...
Hi, We are using nrf9160 and building the application with CMSE. When my program accesses dynamically requested memory (address 0x200128b0), the program automatically jumps...
We plan to use the Nordic Semi Thingy will be used with Quectel YB0014AA antenna for the demo sites, all located in North America. The Nordic Thingy is fully FCC/ISED compliant...
Hi,
I am evaluating using NRF9161-LACA in a design. Is it possible to activate this chip with esim? Or we have to use a physical sim card for it?
Please let me know, ...
